Search found 28 matches

by farmerboy32
Tue Jul 15, 2014 7:42 pm
Forum: Off-Topic Hobbies
Topic: Request for Milled QEV
Replies: 4
Views: 909

Re: Request for Milled QEV

Ohh, my bad. Thanks though. Question, is there any key things i should search for in particular?
by farmerboy32
Sat Jul 12, 2014 8:00 am
Forum: Off-Topic Hobbies
Topic: Request for Milled QEV
Replies: 4
Views: 909

Request for Milled QEV

Hello, i would like to request to any one that has the tools and the spare time a QEV. I would like for it to be able to take up 300# and for it to as asmall as possible. The largest dimensions i would want are 1/2" in width 3-4" in height and 4-5" in length. The ports need to be standard 1/2" threa...
by farmerboy32
Sat Aug 20, 2011 2:37 pm
Forum: Pneumatic Cannons
Topic: trigger mecanism for hammer valve
Replies: 37
Views: 6290

that is a great diagram there jack! :D
by farmerboy32
Thu Aug 11, 2011 8:45 am
Forum: Pneumatic Cannons
Topic: Modified Paintball gun to air rifle/cannon
Replies: 21
Views: 8358

watch the speed on the stun darts, they may break eye wear.
by farmerboy32
Tue Jul 26, 2011 8:07 pm
Forum: Pneumatic Cannons
Topic: Bolt action co-ax IDEA
Replies: 10
Views: 1197

@Mr.Tallahassee, i was thinking it would be able to shoot ball bearings, bb's , etc. so the pipe would just need to be bent,and not 90 degree elbows.
by farmerboy32
Tue Jul 26, 2011 5:15 pm
Forum: Pneumatic Cannons
Topic: Bolt action co-ax IDEA
Replies: 10
Views: 1197

Bolt action co-ax IDEA

this is a idea i had while day-dreaming at work the other day haha.
leave any questions or comments below and i will address them as best as i can.
by farmerboy32
Sun Jul 24, 2011 7:38 am
Forum: BB, Airsoft, and Pellet Guns
Topic: What do i do with this fridge compressor? + Funny story :S
Replies: 10
Views: 2200

the one i had wired up had no capacitor, just the three pegs under the black plastic covering. I took the original power cable and just wired the three cables in the power line to those pegs with a soldering gun. Then i interrupted one of the three cable in the power cable with a switch,so i could t...
by farmerboy32
Sun Jul 17, 2011 7:24 am
Forum: Pneumatic Cannons
Topic: Making a breech loader for my golf ball launcher
Replies: 14
Views: 2327

try using the search tool, because there are many different ways you can do this. The sleeving you mentioned should work, but there are more "gun like" options you may want to try.
by farmerboy32
Sat Jul 16, 2011 11:21 pm
Forum: Pneumatic Cannons
Topic: Higher psi's
Replies: 18
Views: 1433

many junk yards will let you have the fridge compressor for real cheap because they scrap everything anyways. i payed 5$ for my pump :D
by farmerboy32
Thu Jul 14, 2011 6:36 pm
Forum: General How-To & Discussion
Topic: high pressure air line
Replies: 4
Views: 1288

If you check a any place like auto-zone, they sell grease gun line, which is really flexible and it is rated up to 3000 p.s.i The connections on it are 1/8"
by farmerboy32
Thu Jul 14, 2011 6:34 pm
Forum: Pneumatic Cannons
Topic: Made my first airgun + temp trigger rig....
Replies: 13
Views: 2278

that looks like its going to be really cool when its done! :D
by farmerboy32
Wed Jul 13, 2011 4:22 pm
Forum: Pneumatic Cannons
Topic: sprung ball valve hand cannon
Replies: 16
Views: 6289

this is really awesome dude! i really like your clean trigger setup! keep the good work!
by farmerboy32
Mon Jul 11, 2011 10:43 am
Forum: Off-Topic Hobbies
Topic: Magnet properties
Replies: 5
Views: 398

hah jack you just made my morning!
by farmerboy32
Thu Jul 07, 2011 9:33 pm
Forum: Pneumatic Cannons
Topic: Pneumatic repeater prototype.
Replies: 14
Views: 2137

the results of your tinkering with this design should generate some very nice results! keep up the work, and keep us posted! :D
by farmerboy32
Fri Jul 01, 2011 9:07 pm
Forum: Pneumatic Cannons
Topic: My third airgun.
Replies: 12
Views: 3508

that bi-pod is massive. very nice work on the trigger. Your woodworking skills are beyond that of mine, haha!