Search found 70 matches

by Haniball1337
Fri Feb 21, 2020 11:55 am
Forum: BB, Airsoft, and Pellet Guns
Topic: Hammer valve Tee style
Replies: 2
Views: 2908

Re: Hammer valve Tee style

Compression fittings are two 1/2 extensions and I was only having 1/2 rubber washers that have 6 mm ID and the nail diameter is 5mm. I want use that valve for 100-150 bars , maybe less. Yesterday I putted 2 rubber washers in compresion fitting and air was not leaking but it wont move without lubrica...
by Haniball1337
Wed Feb 12, 2020 3:33 pm
Forum: BB, Airsoft, and Pellet Guns
Topic: Hammer valve Tee style
Replies: 2
Views: 2908

Hammer valve Tee style

Hi , i liked pcp airguns and decided to build one but i dont like style of normal hammer valves. I decided to try build a hammer valve where I can put the barrel in front of the valve. I builded something like this on the picture. Air is escaping like sieve from the back where is the squished rubber...
by Haniball1337
Tue Jan 07, 2020 8:05 am
Forum: SpudFiles Discussion
Topic: Magazine problem
Replies: 4
Views: 7452

Re: Magazine problem

What if i will remove magnet detent and I will make ball detent?
by Haniball1337
Sun Jan 05, 2020 7:36 am
Forum: SpudFiles Discussion
Topic: Magazine problem
Replies: 4
Views: 7452

Re: Magazine problem

I have tried similar and it will always happen like that, there is too much air just to launch one BB, it will try to launch the next one or two at a reduced velocity, so they just roll down the barrel. If you want semi auto you need to block the magazine tube somehow between each shot, that's the ...
by Haniball1337
Sat Jan 04, 2020 4:58 pm
Forum: SpudFiles Discussion
Topic: Magazine problem
Replies: 4
Views: 7452

Magazine problem

Hi guys , Happy New Year :D . As always i have problem... I just started building a 4,5 mm BB Semi auto Airgun , but the magazine doesnt work that i wanted. QEV is piloted by 1/8, 5/2 solenoid valve converted into 3/2 NO. Magazine is gravity feed (with spring the same happens) and detent is a magnet...
by Haniball1337
Mon Dec 16, 2019 1:33 pm
Forum: General How-To & Discussion
Topic: Short question topic
Replies: 1502
Views: 536544

Re: Short question topic

Hi , short questions :D Can I connect this two 4,5 mm barrels in one longer like this? I have short barrel and I want now it little longer. I will just put this two OD 6mm tubes in one 6 ID tube. Will it work? Will it ruin accuracy? Can the power decrease?
by Haniball1337
Wed Dec 04, 2019 3:29 pm
Forum: Pneumatic Cannons
Topic: Side lever for the hammer
Replies: 16
Views: 10757

Re: Side lever for the hammer

Hah, I watched all his videos last time even liked them all. This guy is doing great job , I'm curious what is the highest pressure that he put in this tank. I also want to know more about this side lever.
by Haniball1337
Fri Jul 12, 2019 8:19 am
Forum: BB, Airsoft, and Pellet Guns
Topic: Oxygen tank
Replies: 27
Views: 13219

Re: Oxygen tank

I have paintball bottle which has PH 300 bar and there is on bottle tap about thread size. It say 5/8 18 UNF. I tried 5/8 thread and it's too big for it. bottle only fits 3/8 but for 2 tooths. Photo: https://imagizer.imageshack.com/img924/3833/lvWNJ7.jpg I look on internet for 5/8 - 18 UNF and i fou...
by Haniball1337
Mon Jul 08, 2019 4:06 am
Forum: Combustion Cannons
Topic: Combustion Cannon with stand
Replies: 2
Views: 3035

Re: Combustion Cannon with stand

Thanks. I don't see on bottle any words about mix.
by Haniball1337
Sun Jul 07, 2019 7:11 am
Forum: Combustion Cannons
Topic: Combustion Cannon with stand
Replies: 2
Views: 3035

Combustion Cannon with stand

Hi everyone. I want show you my Potato gun, what I made. For me it is little ugly. I need to clean it but it works and it is fueled via 100 ml syringe :D btw sorry for my bad english. I fuel the gun from syringe using 100 ml of propane-butane and cannon never almost failed. Is it good ratio of fuel?...
by Haniball1337
Sun Jul 07, 2019 5:11 am
Forum: BB, Airsoft, and Pellet Guns
Topic: Oxygen tank
Replies: 27
Views: 13219

Re: Oxygen tank

Nevermind i think i will not use ball valve. I just found a pcp one way filling valve for 10$. Something like this
by Haniball1337
Sat Jul 06, 2019 2:48 pm
Forum: BB, Airsoft, and Pellet Guns
Topic: Oxygen tank
Replies: 27
Views: 13219

Re: Oxygen tank

Ok thanks for info
by Haniball1337
Sat Jul 06, 2019 2:01 pm
Forum: BB, Airsoft, and Pellet Guns
Topic: Oxygen tank
Replies: 27
Views: 13219

Re: Oxygen tank

You're right. I think i will buy high pressure rated fittings because i dont want risk. I even found that 250+ bar rated tee costs less than this 25 bar rated tee... How about 3000 psi rated aluminum paintball tank Can i take it to 300 bar?
by Haniball1337
Sat Jul 06, 2019 3:30 am
Forum: BB, Airsoft, and Pellet Guns
Topic: Oxygen tank
Replies: 27
Views: 13219

Re: Oxygen tank

So it wont be able to hold that? I found that Joerg Sprave was using ball valve rated to 150 psi and it was able to hold 200 bar.
by Haniball1337
Fri Jul 05, 2019 2:23 pm
Forum: BB, Airsoft, and Pellet Guns
Topic: Oxygen tank
Replies: 27
Views: 13219

Re: Oxygen tank

I have another question. Will this steel tee and ball valve hold 200 bar pressure? Steel Tee has pressure rating to 25 bar. Brass ball valve has 30 bar rating.