Bushing modification - Revision history

Hubb017 at 19:46, 25 March 2009

2009-03-25T19:46:08Z

← Older revision		Revision as of 14:46, 25 March 2009
Line 1:		Line 1:
	Bushing modification refers to removing the stop built into a reducing or hub [[bushing]], so that a pipe may freely pass through. This is commonly done when fabricating [[coaxial]] cannons and [[piston valve]]s.		Bushing modification refers to removing the stop built into a reducing or hub [[bushing]], so that a pipe may freely pass through. This is commonly done when fabricating [[coaxial]] cannons and [[piston valve]]s.

			Several methods exist that can be used to remove the lip from a bushing. One of the easiest ways is to use a Dremel or other rotary tool. Sandpaper or a file can also be used.

			The best method of doing this is to remove only portions of the lip at a time. Check the pipe inside the bushing periodically until it will fit.

	[[Category:Construction methods]]		[[Category:Construction methods]]
	~~[[Category:Stubs]]~~

Benstern: added link and two categories

2008-06-01T13:22:14Z

added link and two categories

← Older revision		Revision as of 08:22, 1 June 2008
Line 1:		Line 1:
	Bushing modification refers to removing the stop built into a reducing or hub bushing, so that a pipe may freely pass through. This is commonly done when fabricating [[coaxial]] cannons and [[piston valve]]s.		Bushing modification refers to removing the stop built into a reducing or hub [[bushing]], so that a pipe may freely pass through. This is commonly done when fabricating [[coaxial]] cannons and [[piston valve]]s.

			[[Category:Construction methods]]
			[[Category:Stubs]]

BC Pneumatics at 08:48, 31 May 2008

2008-05-31T08:48:14Z

← Older revision		Revision as of 03:48, 31 May 2008
Line 1:		Line 1:
	~~Take~~ a ~~file (~~or ~~[[Dremel]]~~, ~~[[lathe]], whatnot), and remove the lip from the inside of~~ a ~~bushing. This allows the~~ pipe ~~to go~~ through ~~the reducing bushing~~.		Bushing modification refers to removing the stop built into a reducing or hub bushing, so that a pipe may freely pass through. This is commonly done when fabricating [[coaxial]] cannons and [[piston valve]]s.

	This is done ~~to allow~~ [[~~co-axial~~]] ~~launcher construction.~~
	~~Bushing in black:~~
	[[~~Image:Bushing mod.PNG]]~~
	~~[[Category:Construction methods~~]]

GalFisk: +cat

2005-10-25T11:23:40Z

+cat

← Older revision		Revision as of 06:23, 25 October 2005
Line 4:		Line 4:
	Bushing in black:		Bushing in black:
	[[Image:Bushing mod.PNG]]		[[Image:Bushing mod.PNG]]
			[[Category:Construction methods]]

GalFisk: typo, +links

2005-10-19T08:08:10Z

typo, +links

← Older revision		Revision as of 03:08, 19 October 2005
Line 1:		Line 1:
	Take a file (or ~~dremmle~~, lathe, whatnot), and remove the lip from the inside of a bushing. This allows the pipe to go through the reducing bushing.		Take a file (or [[Dremel]], [[lathe]], whatnot), and remove the lip from the inside of a bushing. This allows the pipe to go through the reducing bushing.

	This is done to allow [[co-axial]] launcher construction.		This is done to allow [[co-axial]] launcher construction.
	Bushing in black:		Bushing in black:
	[[Image:Bushing mod.PNG]]		[[Image:Bushing mod.PNG]]

Boilingleadbath at 01:03, 19 October 2005

2005-10-19T01:03:42Z

← Older revision		Revision as of 20:03, 18 October 2005
Line 1:		Line 1:
	Take a file (or dremmle, lathe, whatnot), and remove the lip from the inside of a bushing. This allows the pipe to go through the reducing bushing.		Take a file (or dremmle, lathe, whatnot), and remove the lip from the inside of a bushing. This allows the pipe to go through the reducing bushing.

	This is done to allow [[co axial]] launcher construction.		This is done to allow [[co-axial]] launcher construction.
	Bushing in black:		Bushing in black:
	[[Image:Bushing mod.PNG]]		[[Image:Bushing mod.PNG]]

Boilingleadbath at 01:02, 19 October 2005

2005-10-19T01:02:50Z

New page

Take a file (or dremmle, lathe, whatnot), and remove the lip from the inside of a bushing. This allows the pipe to go through the reducing bushing.

This is done to allow [[co axial]] launcher construction.
Bushing in black:
[[Image:Bushing mod.PNG]]