Search found 543 matches

Return

by Anatine Duo
Fri Jan 17, 2020 6:41 pm
Jump to forum
Jump to topic

compact precision launcher

Velocity test on a can of water:



Almost finished...

It has a 1/2" qev, 0.875" barrel. My first breechloader I think. Barrel short enough to muzzleload an arrow.

Going for a California-legal look.
by Gippeto
Mon Jan 20, 2020 10:48 am
Jump to forum
Jump to topic

Re: "In the world of spuds today"

Manual recommends the following: ten days after the machine is put into normal use, it is necessary to change the oil in the headstock. Do you think that's enough? Changed the oil in mine before I ran it in and after. Now change it yearly. Doesn't hold much oil so it's cheap insurance. Don't forget...
by mrfoo
Sun Feb 16, 2020 1:40 am
Jump to forum
Jump to topic

Re: Low-friction/Specialty Ball Valves?

Here's one, for example : https://www.valvesonline.co.uk/manual-v ... l-bkh.html

Relatively cheap, pom / molybdenum disulphide seals, rated for 500 bar.
by hectmarr
Sat Feb 15, 2020 10:05 pm
Jump to forum
Jump to topic

Re: Low-friction/Specialty Ball Valves?

If you are using a manual air pump, the lubrication system goes into it. In the case you use a motocompressor, it is the same. Always the air that comes out will be lubricated. Commercial devices are not very expensive. I suggest you study thoroughly, what kind of lubricant is a friend of the seal m...
by Potato Demon
Thu Feb 20, 2020 3:07 pm
Jump to forum
Jump to topic

Re: SpudFiles has entered 2020

Nice! I haven’t logged on in quite a while and I love how the new design looks!
by blk94f150
Fri Feb 21, 2020 11:44 am
Jump to forum
Jump to topic

Shooting various materials with my spud gun



Hi guys! I made this video of my spud cannon shooting through a bunch of different materials. Enjoy!
by hectmarr
Mon Feb 24, 2020 2:19 pm
Jump to forum
Jump to topic

Re: Single pumping hybrid, "Strong Boy"

Successful test run! :D The simple charger works perfectly, makes a metallic sound barely perceptible and most importantly, does not fail. I have charged about 200 bb´s and the small battery seems to still have a lot of charge. The idea is that in the real weapon, the tube that houses the bb's, is b...
by hectmarr
Sun Feb 23, 2020 6:03 pm
Jump to forum
Jump to topic

Re: Single pumping hybrid, "Strong Boy"

I am building this charger to provide future "Strong Boy´s" mono pumping, with a very simple system of loading 1/4 "bb's. :D The idea is not to complicate the weapon, I want it very simple, but avoid loading the ammunition through the firing cannon with the drumstick. It is what does not conform me ...
by hectmarr
Wed Feb 26, 2020 3:04 pm
Jump to forum
Jump to topic

Re: Single pumping hybrid, "Strong Boy"

Hi Jack! Nice to see you here. :D I saw your drawing and it's good. I think the solution, for your specific case and the power of the solenoid. Many amps will be necessary to overcome the resistance of the o´ring, and little more than that. According to what I have tried, with about 800 w, it would ...
by blk94f150
Sat Mar 07, 2020 3:51 pm
Jump to forum
Jump to topic

Shooting more stuff with my spud gun! Watermelon and a couple boards



I got a request to blast a watermelon so I did that, some osb, and plywood. Enjoy!
by mrfoo
Mon Mar 09, 2020 2:12 pm
Jump to forum
Jump to topic

Re: JSR's workshop chronicles

It's almost certainly due to burrs or shite geometry, but it could be problems with the handwheel, bent screw, etc. First thing to try would be to remove the handwheel parts entirely, reassemble the rest of the slide, adjust the gibs to "close enough but a bit slack" and see if you can slide it smoo...
by Gippeto
Wed Mar 11, 2020 12:33 pm
Jump to forum
Jump to topic

Re: JSR's workshop chronicles

I rarely use the compound unless cutting tapers. For longitudinal turning, any misalignment will throw diameters off. I actually have one qctp setup that mounts directly to the cross slide...no compound at all. Chamfers and threading are accomplished by tool geometry alone. For the diy dro, I'm usin...
by mrfoo
Wed Mar 11, 2020 12:13 pm
Jump to forum
Jump to topic

Re: JSR's workshop chronicles

Oh, my. That's shit design. Really shit design. What I'd probably do, if possible, would be to find a way to position and then block #25 exactly where it should be, /temporarily/, then drill and ream for a couple of locating pins to hold everything square. You can then enlarge the bolt holes if nece...
by Moonbogg
Wed Mar 11, 2020 11:02 am
Jump to forum
Jump to topic

Re: JSR's workshop chronicles

JSR, could it be an option to apply an abrasive polishing paste between the rough parts and work them back and forth, allowing them to polish themselves in a natural way? Just a thought. I'm sick with jealousy by the way. SICK! Not coronavirus sick, but still quit green with machine envy :mrgreen: