When drilling and tapping PVC...
-
Kris.Is.Awesome
- Private 4
- Posts: 72
- Joined: Tue Jul 11, 2006 2:52 pm
- Location: Virginia Beach, VA
- Contact:
Do I want to drill and tap through just the PVC tube, or go through the tube, and a fitting aswell?
when i have to screw stuff into my pipes i just drill a hole that is a little smaller than what im inserting then i just screw it into it and it makes its own threds then i take it out and out some "tape" on it then reinsert it. and that usually sealls it tight but if i rly need more i just put some apoxey.
-
Kris.Is.Awesome
- Private 4
- Posts: 72
- Joined: Tue Jul 11, 2006 2:52 pm
- Location: Virginia Beach, VA
- Contact:
I know how to drill and tap, I just need to know if I should put it through a fitting- maybe it's stronger.
Can I mount it like this? Is that fitting strong enough to mount it on the 'slant'? Or should I mount it on the flat part- or maybe just the tube?
It's one of theese fittings- I wanna put it on the slant.
Can I mount it like this? Is that fitting strong enough to mount it on the 'slant'? Or should I mount it on the flat part- or maybe just the tube?
It's one of theese fittings- I wanna put it on the slant.
Last edited by Kris.Is.Awesome on Mon Jul 31, 2006 3:14 pm, edited 1 time in total.
-
LucyInTheSky
- Specialist 2
- Posts: 293
- Joined: Fri Apr 21, 2006 11:46 am
Mount it so it goes through two layer of PVC where the fitting and Pipe overlap.
-
Kris.Is.Awesome
- Private 4
- Posts: 72
- Joined: Tue Jul 11, 2006 2:52 pm
- Location: Virginia Beach, VA
- Contact:
LucyInTheSky wrote:Mount it so it goes through two layer of PVC where the fitting and Pipe overlap.
Okay- thanks. Will do.
-
Kris.Is.Awesome
- Private 4
- Posts: 72
- Joined: Tue Jul 11, 2006 2:52 pm
- Location: Virginia Beach, VA
- Contact:
markfh11q wrote:That looks like a DWV reducing coupling. Not safe for a pneumatic at all...
That picture was to illustrate the general coupling I used- Are you saying it's a bad Idea?
-
Shrimphead
- Corporal
- Posts: 509
- Joined: Thu Nov 17, 2005 7:42 pm
Check to see if the fitting says "NSF-pw" on it. If it doesn't than it means that it's not a pressure rated fitting.
Controlled insanity = Genius
Life flies when you're being dumb.
Life flies when you're being dumb.
Mer... The whole reason why it is recommended that you tap threw two layers of PVC is so that the component being "tapped" into there has more material to "grip" on.
Im not completly sure on this, but if I recall correctly reducing/increasing couplings are a thing of the "non-pressure rated" realm, regardless of manufactuer. Ive used them in pneumatics up to 125PSI (thats as high as my compressor goes). I wouldnt scrap your whole gun over such a fitting, but for futures safety Id recommend pressure rated bushings in future builds.
Im not completly sure on this, but if I recall correctly reducing/increasing couplings are a thing of the "non-pressure rated" realm, regardless of manufactuer. Ive used them in pneumatics up to 125PSI (thats as high as my compressor goes). I wouldnt scrap your whole gun over such a fitting, but for futures safety Id recommend pressure rated bushings in future builds.
Going through 2 layers would be best. And I don't care what other people say, use a drill and tap to cut your threads. You can buy taps seperately, and they are only like $3 or $4 each, so they aren't that expensive. And if it's something like a 1/4 NPT tap, it will get plenty of use to justify that expense.
And by the way, ball valves don't have that good of performance. Sprinkler vavles > ball valves.
And by the way, ball valves don't have that good of performance. Sprinkler vavles > ball valves.
-
LucyInTheSky
- Specialist 2
- Posts: 293
- Joined: Fri Apr 21, 2006 11:46 am
and QEV > sprinkler valves
-
Flying_Salt
- Corporal 3
- Posts: 779
- Joined: Mon Oct 09, 2006 4:57 pm
- Location: Texas
And just to be safe if you wanna, do what I do and put a bit of caulk on there. it helps seal it off.
