plumber's vs. Gas type
-
koolaidman
- Specialist
- Posts: 156
- Joined: Sun Jun 24, 2007 7:46 pm
quick question. Is it ok to use regular plumber's teflon instead of the one for gas? (the white tape instead of the yellow)
-
Pete Zaria
- Corporal 5
- Posts: 954
- Joined: Fri Mar 31, 2006 6:04 pm
- Location: Near Seattle, WA
For what application?
I use the regular white Teflon tape with brass and PVC fittings, for low-to-medium pressure applications with no problems.
I wouldn't use it on an unregulated CO2 system but shy of that I think the regular teflon tape is fine.
Peace,
Pete Zaria.
I use the regular white Teflon tape with brass and PVC fittings, for low-to-medium pressure applications with no problems.
I wouldn't use it on an unregulated CO2 system but shy of that I think the regular teflon tape is fine.
Peace,
Pete Zaria.
-
koolaidman
- Specialist
- Posts: 156
- Joined: Sun Jun 24, 2007 7:46 pm
its gonna be for steel, iron, and copper, up to 200 psi maybe (air.)
-
Pete Zaria
- Corporal 5
- Posts: 954
- Joined: Fri Mar 31, 2006 6:04 pm
- Location: Near Seattle, WA
I've used the white teflon tape on brass up to and over that pressure before.
Try it and see if it leaks at all (use soapy water or etc.. to test). I like 2-3 wraps of teflon tape, and two wrenches to really tighten down the fittings. If it doesn't leak, you're good
Peace,
Pete Zaria.
Try it and see if it leaks at all (use soapy water or etc.. to test). I like 2-3 wraps of teflon tape, and two wrenches to really tighten down the fittings. If it doesn't leak, you're good
Peace,
Pete Zaria.
-
Gippeto
- First Sergeant 3
- Posts: 2503
- Joined: Sat Jan 19, 2008 10:14 am
- Location: Soon to be socialist shit hole.
- Has thanked: 2 times
- Been thanked: 17 times
White teflon is fine. I use it to 7000 psi on a regular basis for hydraulic applications. Save the gas stuff for gas apps.
"It could be that the purpose of your life is to serve as a warning to others" – unknown
Liberalism is a mental disorder, reality is it's cure.
Liberalism is a mental disorder, reality is it's cure.
-
SpudMonster
- Specialist 2
- Posts: 250
- Joined: Mon Aug 08, 2005 5:54 pm
White works fine. Just give it a few extra wraps.
Gippeto, this is a gas application. He's using air, not hydraulic oil.
And the tape on the joints on my SCTBDC is white teflon tape. As a general rule, I use about 120" of tape on a 2" fitting. 1/4" fittings seal perfectly with only 18" or so. I go through tape quickly, but everything seals fine.
The only yellow gas tape I've seen around here was only rated for 100 psi.
And the tape on the joints on my SCTBDC is white teflon tape. As a general rule, I use about 120" of tape on a 2" fitting. 1/4" fittings seal perfectly with only 18" or so. I go through tape quickly, but everything seals fine.
The only yellow gas tape I've seen around here was only rated for 100 psi.
Spudfiles' resident expert on all things that sail through the air at improbable speeds, trailing an incandescent wake of ionized air, dissociated polymers and metal oxides.
-
bigbob12345
- Staff Sergeant
- Posts: 1516
- Joined: Sat Dec 01, 2007 9:13 am
- Location: Mercer Island,Washington
I always use the white stuff because its $1 for a 260in roll and the yellow gas stuff is $3 for a 200in roll. Ive never had any problems with leaks from it except on pvc fittings but i probaly just didnt put enough.
i have used the gas stuff before because i just had some laying around and I actually had problems with getting it to seal.
Ther is also that pink stuff which is even more expencive but Ive never tryed it.
the white tape is better and cheaper.
i have used the gas stuff before because i just had some laying around and I actually had problems with getting it to seal.
Ther is also that pink stuff which is even more expencive but Ive never tryed it.
the white tape is better and cheaper.
-
Gippeto
- First Sergeant 3
- Posts: 2503
- Joined: Sat Jan 19, 2008 10:14 am
- Location: Soon to be socialist shit hole.
- Has thanked: 2 times
- Been thanked: 17 times
My bad.
How about..."Save the expensive colour coded teflon tape for applications which require a colour code."
Use yellow for natural gas
Use green for oxygen
Use which ever you want on air, water and apparently nitrogen too.
How about..."Save the expensive colour coded teflon tape for applications which require a colour code."
Use yellow for natural gas
Use green for oxygen
Use which ever you want on air, water and apparently nitrogen too.
"It could be that the purpose of your life is to serve as a warning to others" – unknown
Liberalism is a mental disorder, reality is it's cure.
Liberalism is a mental disorder, reality is it's cure.
-
D_Hall
- Staff Sergeant 5
- Posts: 1920
- Joined: Thu Feb 07, 2008 7:37 pm
- Location: SoCal
- Has thanked: 7 times
- Been thanked: 42 times
One thing to keep in mind....
Strictly speaking, the teflon tapes aren't supposed to be sealants. They're supposed to be dry lubricants that allow you to tighten the pipe threads properly, blah blah blah.
Anywho, a trick I picked up back when I used to tinker with paintball equipment: Forget teflon tape. Go get yourself some blue Loc-Tite. Use it liberally on the threads in question.
I've had plenty of joints leak when using teflon tape. I've NEVER had a joint leak with Loc-Tite.
Note: The above trick applies to metal construction only. With PVC? Yeah, teflon tape.
Strictly speaking, the teflon tapes aren't supposed to be sealants. They're supposed to be dry lubricants that allow you to tighten the pipe threads properly, blah blah blah.
Anywho, a trick I picked up back when I used to tinker with paintball equipment: Forget teflon tape. Go get yourself some blue Loc-Tite. Use it liberally on the threads in question.
I've had plenty of joints leak when using teflon tape. I've NEVER had a joint leak with Loc-Tite.
Note: The above trick applies to metal construction only. With PVC? Yeah, teflon tape.
If you use Loc-Tite its a pain in the a$$ to unscrew the joints if you change your mind later on. Especially on larger fittings. With paintball the average connection size is 1/4" or 1/8" NPT and the pressure is usually 200-800psi when full, so you need the Loc-Tite on certain paintball applications where teflon won't cut it.