LOL, my part of fail (reading on my phone isn't very easy )
According to your animation, I should place 2 pumps one each side... Longer hose and double dead space, or I didn't follow your idea :p
High pressure compressor
- wyz2285
- First Sergeant 2
- Posts: 2385
- Joined: Sat Mar 06, 2010 7:50 am
- Location: Porto, Portugal
- Has thanked: 1 time
- Been thanked: 3 times
- Contact:
CpTn_lAw wrote: "yay, me wanna make big multishot pnoob with 1000 psi foot pump compressor using diamond as main material. Do you think wet bread make good sealant? "
- jackssmirkingrevenge
- Five Star General
- Posts: 26179
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 543 times
- Been thanked: 321 times
You don't *have* to be pumping in both directions, but if you do you will pump twice as fastwyz2285 wrote:According to your animation, I should place 2 pumps one each side... Longer hose and double dead space, or I didn't follow your idea :p
Dead space from the hoses is not that critical, your biggest concern should the dead space between piston head and check valve as ultimately this will limit the maximum pressure you can reach.
By the way, don't forget spudamine's two stage pump design: http://www.spudfiles.com/pneumatic-cann ... 18170.html
hectmarr wrote:You have to make many weapons, because this field is long and short life
- wyz2285
- First Sergeant 2
- Posts: 2385
- Joined: Sat Mar 06, 2010 7:50 am
- Location: Porto, Portugal
- Has thanked: 1 time
- Been thanked: 3 times
- Contact:
Too many o-rings, but kind of what I was thinking, half cycle for high pressure fill and other half for low pressure. I didn't mean the hose dead volume but extra hose -> extra fittings -> extra cost :p quite obvious I know where is the dead volume in a pump.
CpTn_lAw wrote: "yay, me wanna make big multishot pnoob with 1000 psi foot pump compressor using diamond as main material. Do you think wet bread make good sealant? "
- jackssmirkingrevenge
- Five Star General
- Posts: 26179
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 543 times
- Been thanked: 321 times
Not an excuse when you have a latheToo many o-rings
You can have a single piston, it will just take longer to fill but on the plus side, much less dead volume.
hectmarr wrote:You have to make many weapons, because this field is long and short life
- wyz2285
- First Sergeant 2
- Posts: 2385
- Joined: Sat Mar 06, 2010 7:50 am
- Location: Porto, Portugal
- Has thanked: 1 time
- Been thanked: 3 times
- Contact:
Need to play with the variables for a little, will post a 3D model later.
For now, I have a calculus test to worry about.
Anyway thanks JSR, watch this place
For now, I have a calculus test to worry about.
Anyway thanks JSR, watch this place
CpTn_lAw wrote: "yay, me wanna make big multishot pnoob with 1000 psi foot pump compressor using diamond as main material. Do you think wet bread make good sealant? "
- jackssmirkingrevenge
- Five Star General
- Posts: 26179
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 543 times
- Been thanked: 321 times
bonne chance
hectmarr wrote:You have to make many weapons, because this field is long and short life
- wyz2285
- First Sergeant 2
- Posts: 2385
- Joined: Sat Mar 06, 2010 7:50 am
- Location: Porto, Portugal
- Has thanked: 1 time
- Been thanked: 3 times
- Contact:
Thanks, will need it. Worked pretty hard though, should get me through the semester
CpTn_lAw wrote: "yay, me wanna make big multishot pnoob with 1000 psi foot pump compressor using diamond as main material. Do you think wet bread make good sealant? "
- killerbanjo
- Specialist 2
- Posts: 245
- Joined: Fri Jun 18, 2010 6:56 pm
Hey man, would something like this not be easier? The large piston would be better off being almost balanced at first so it allows the front area to get to a reasonable pressure before compressing it but its an old drawing and I can't be bothered to edit it for now... Of course you would still need a shop compressor.