Best type of QEV? (and pilot/fill valve)
- Hailfire753
- Specialist 3
- Posts: 348
- Joined: Thu Jun 28, 2007 11:50 pm
- Location: Near Philadelphia, PA
It's summer, and I would like to start making a paintball gun as soon as I can convince my dad.
The gun will use a QEV/ homemade sleeve valve combo to achieve semi/auto fire. I plan to use a 3/4 QEV, but I need it as small, fast, lightweight, and cheap as possible, and with a high flow. I would like it to be able to tolerate high-as-possible pressures, but this is for off-field target carnage (around 20 psi on field, up to CO2 pressure off-field.)
From what I understand, there are two factors affecting valve performance: opening time and Cv, or flow coefficient. There are several types and brands of QEVs I have seen, some using diaphragms, others using shuttles.
Question 1: Do shuttle QEVs open faster than diaphragm QEVs?
Question 2: Are diaphragm QEVs able to handle 150+ psi past their rating like shuttle QEVs?
This site shows what appears to be a 3/4" shuttle QEV with a CV of 4.08. This site (.pdf warning) shows a 3/4 diaphragm QEV with a CV of 10.55. I am leaning toward the diaphragm, but it appears to be bigger and heavier than the shuttle. Prices are not listed. Also, different companies use different ways to measure CV, but it is generally calculated as the number of gallons of water that can flow through the valve at 100 psi with a 10 psi drop in pressure per minute.
Question 3: What kind of performance difference would I see between the two?
For paintball, I need EXTREME fill speed (Cv), a cycle rate of around 10 per second, and little pilot air.
Also, I would be grateful for any suggestions for alternative QEVs or a completely different valve setup.
Shuttle QEV
Diaphragm QEV
The gun will use a QEV/ homemade sleeve valve combo to achieve semi/auto fire. I plan to use a 3/4 QEV, but I need it as small, fast, lightweight, and cheap as possible, and with a high flow. I would like it to be able to tolerate high-as-possible pressures, but this is for off-field target carnage (around 20 psi on field, up to CO2 pressure off-field.)
From what I understand, there are two factors affecting valve performance: opening time and Cv, or flow coefficient. There are several types and brands of QEVs I have seen, some using diaphragms, others using shuttles.
Question 1: Do shuttle QEVs open faster than diaphragm QEVs?
Question 2: Are diaphragm QEVs able to handle 150+ psi past their rating like shuttle QEVs?
This site shows what appears to be a 3/4" shuttle QEV with a CV of 4.08. This site (.pdf warning) shows a 3/4 diaphragm QEV with a CV of 10.55. I am leaning toward the diaphragm, but it appears to be bigger and heavier than the shuttle. Prices are not listed. Also, different companies use different ways to measure CV, but it is generally calculated as the number of gallons of water that can flow through the valve at 100 psi with a 10 psi drop in pressure per minute.
Question 3: What kind of performance difference would I see between the two?
For paintball, I need EXTREME fill speed (Cv), a cycle rate of around 10 per second, and little pilot air.
Also, I would be grateful for any suggestions for alternative QEVs or a completely different valve setup.
Shuttle QEV
Diaphragm QEV
Last edited by Hailfire753 on Tue Jun 10, 2008 9:32 am, edited 1 time in total.
UPDATED MARCH '08
field-legal paintball semi
field-legal paintball semi
- POLAND_SPUD
- Captain
- Posts: 5402
- Joined: Sat Oct 13, 2007 4:43 pm
- Been thanked: 1 time
good combination - AFAIK ragnarok used it.. I am planning to do the sameThe gun will use a QEV/ homemade sleeve valve
I suppose that the Shuttle QEV is beter... it seems more sturdy.. perdonaly I use the shuttle QEV and it works fine to 450 - 500 psi
most europeans use Shuttle QEV
Children are the future
unless we stop them now
unless we stop them now
Shuttle eh? I've always called them piston types.
As you can see from this diagram, both types have a moving part, the diaphragm is not clamped but is free to flex its edges to allow air past in filling and its centre to allow for exhausting.
Anyway the primary advantage of the "shuttle" type is the fact that they don't have the great protruding flanges of the diaphragm type.
I have seen that diaphragm types appear to have greater flow than shuttle types but I didn't think it was more than double. Oddly enough I'm certain I've also read that shuttles are designed to provide greater flow than "normal" diaphragm types.
I'll look about.
The smallest QEV you're comfortable with will keep the pilot volume down and a slide valve screwed right into the fill point will give absolute minimum pilot volume.
The ROF is actually more likely to depend on the slide valves flow than the QEV's as you really will not want to be operating a 3/4" slide valve with a finger at any high rate. In fact no paintball guns operate the main valves directly, usually using fiddly pneumatics to keep the trigger pull down if they're not electric.
I can't see 10bps with a physically operated pilot valve really.
As you can see from this diagram, both types have a moving part, the diaphragm is not clamped but is free to flex its edges to allow air past in filling and its centre to allow for exhausting.
Anyway the primary advantage of the "shuttle" type is the fact that they don't have the great protruding flanges of the diaphragm type.
I have seen that diaphragm types appear to have greater flow than shuttle types but I didn't think it was more than double. Oddly enough I'm certain I've also read that shuttles are designed to provide greater flow than "normal" diaphragm types.
I'll look about.
The smallest QEV you're comfortable with will keep the pilot volume down and a slide valve screwed right into the fill point will give absolute minimum pilot volume.
The ROF is actually more likely to depend on the slide valves flow than the QEV's as you really will not want to be operating a 3/4" slide valve with a finger at any high rate. In fact no paintball guns operate the main valves directly, usually using fiddly pneumatics to keep the trigger pull down if they're not electric.
I can't see 10bps with a physically operated pilot valve really.
- Hailfire753
- Specialist 3
- Posts: 348
- Joined: Thu Jun 28, 2007 11:50 pm
- Location: Near Philadelphia, PA
Hmm, thanks for the advice. I thought the piston/shuttle QEV to be the more sturdy of the two, and I also heard that those flanges of the diaphragm limit flow. Another site showed the diaphragm at around 7 Cv. Could be a different make, or a different Cv testing method.
Why would I "not want" to operate a 3/4 slide valve quickly? Would the pilot air be annoying/painful? Or would my finger get tired? I don't think it will be an issue, as it is not hard to slide lubed pipe back and forth with no air pressure resistance (I think?). Also, there will be pneumatic assistance in that department.
See the animation, or this.
Why would I "not want" to operate a 3/4 slide valve quickly? Would the pilot air be annoying/painful? Or would my finger get tired? I don't think it will be an issue, as it is not hard to slide lubed pipe back and forth with no air pressure resistance (I think?). Also, there will be pneumatic assistance in that department.
See the animation, or this.
- Attachments
-
[The extension swf has been deactivated and can no longer be displayed.]
UPDATED MARCH '08
field-legal paintball semi
field-legal paintball semi
- potatoflinger
- Sergeant 2
- Posts: 1136
- Joined: Thu Nov 02, 2006 3:26 pm
- Location: Maryland
I have a diaphragm QEV and two shuttle QEVs and I prefer the shuttle QEVs because they fit into a design better (they don't stick out around the sides) but I never bothered to look up which type has better flow.
It's hard to soar with eagles when you're working with turkeys.
- Hailfire753
- Specialist 3
- Posts: 348
- Joined: Thu Jun 28, 2007 11:50 pm
- Location: Near Philadelphia, PA
Hmm... 750 psi? Crazy! I might have to go with a diaphragm just because of that.
QEVs seem pretty hot-swapable, does anyone with both types want to test the performance difference?
Also, a simplified version of the piston valve in clide's slider is an option
EDIT: The 3g iPhone was just released!! 2:40 pm est
QEVs seem pretty hot-swapable, does anyone with both types want to test the performance difference?
Also, a simplified version of the piston valve in clide's slider is an option
EDIT: The 3g iPhone was just released!! 2:40 pm est
UPDATED MARCH '08
field-legal paintball semi
field-legal paintball semi
- Hailfire753
- Specialist 3
- Posts: 348
- Joined: Thu Jun 28, 2007 11:50 pm
- Location: Near Philadelphia, PA
Edit: whoops, double post. accidentally clicked quote instead of edit.
BTW, does anyone have a link to where I could buy an "American style Detrol QEV" or a specs page?
BTW, does anyone have a link to where I could buy an "American style Detrol QEV" or a specs page?
UPDATED MARCH '08
field-legal paintball semi
field-legal paintball semi
You will have a tough time pulling a 3/4" slide valve back at CO2 pressures, they even tend to get stuck half way if not pressed hard enough and can leak.
Even with the response trigger system i can't imagine you would ever get 10bps, even with no pressure at all, it would be hard to open a sleeve valve that fast.
Even with the response trigger system i can't imagine you would ever get 10bps, even with no pressure at all, it would be hard to open a sleeve valve that fast.
- MrCrowley
- Moderator
- Posts: 10078
- Joined: Fri Jun 23, 2006 10:42 pm
- Location: Auckland, New Zealand
- Been thanked: 3 times
I'm positive the British piston ones can take that also. I was just saying that it's not only the British one that can take high pressures.Hailfire753 wrote:Hmm... 750 psi? Crazy! I might have to go with a diaphragm just because of that.
Also you can get the American Detrol's on McMaster.
I would suggest Fastenal, I'm not sure if they carry Deltrol valves, but I bought a 3/4" QEV from Alpha Technologies, and it is great.
Fastenal QEV Page.
Fastenal QEV Page.
“He who controls the present, controls the past. He who controls the past, controls the future.”
-George Orwell
-George Orwell
- POLAND_SPUD
- Captain
- Posts: 5402
- Joined: Sat Oct 13, 2007 4:43 pm
- Been thanked: 1 time
al-xg could you say more about slide valves ? I haven o personal experience with them.. are they like QC fittings ? (that is they are harder to open when used at high pressures ?)
Children are the future
unless we stop them now
unless we stop them now
- Hailfire753
- Specialist 3
- Posts: 348
- Joined: Thu Jun 28, 2007 11:50 pm
- Location: Near Philadelphia, PA
I completely forgot about McMaster QEVs, I thought that they were pistons. They show a Cv of 7.84. Thanks MrCrowley.
I took a look at the fastenal 3/4 Alpha QEV, and it shows as .2 lbs, compared to the 2-3 pounds of a 3/4 diaphragm QEV. Is this accurate? Also, Is the alpha QEV the type where the shuttle is rigid or is it rubbery?
As for slide valves, I don't see where or why it would get stuck. Pressure is equalized in both directions, so as far as I know it would not be more difficult to open with more pressure. But then again, I don't have any personal experience either, just common sense physics (could be wrong).
I took a look at the fastenal 3/4 Alpha QEV, and it shows as .2 lbs, compared to the 2-3 pounds of a 3/4 diaphragm QEV. Is this accurate? Also, Is the alpha QEV the type where the shuttle is rigid or is it rubbery?
As for slide valves, I don't see where or why it would get stuck. Pressure is equalized in both directions, so as far as I know it would not be more difficult to open with more pressure. But then again, I don't have any personal experience either, just common sense physics (could be wrong).
UPDATED MARCH '08
field-legal paintball semi
field-legal paintball semi