Almost done!

Show us your pneumatic spud gun! Discuss pneumatic (compressed gas) powered potato guns and related accessories. Valve types, actuation, pipe, materials, fittings, compressors, safety, gas choices, and more.
User avatar
Jack_Hogg
Specialist
Specialist
Posts: 133
Joined: Tue Feb 20, 2007 7:56 am

Thu Oct 15, 2009 1:16 am

I am making a pneumatic airgun for firing marbles. I am busy the last weeks on some things, so I don't have much time to work on my gun.
I am totally new to pneumatic spudguns. Then also this will be my first one 8-) Well, that in mind, I want it to make it preform as good as
it gets. I have made some pictures with my phone, (sony ericsson C510) below:


The gun.
Image

Sealing face.
Image

Pilot.
Image

Piston installed.
Image

How it looks when it seals against the sealing face inside the gun.
Image

Piston.
Image

Another angle.
Image

Another angle.
Image

Trigger, little blurry :(
Image

The 10mm metal bracket. (Made with a laser cutter)
Image

Bracket fixed.
Image

And the ¾'' BSP outside threaded pipe I found on highschool. Used for connecting the T-peices and the endcap. (for make it more compact)
Image
Last edited by Jack_Hogg on Sun Mar 07, 2010 2:09 pm, edited 3 times in total.
User avatar
psycix
Sergeant Major 4
Sergeant Major 4
Posts: 3684
Joined: Mon Jun 25, 2007 7:12 am
Location: The Netherlands

Donating Members

Thu Oct 15, 2009 4:11 am

That looks good! Its shiny, did you polish it?
Your trigger is very BTB, I've got one just like that (from him).

Why is there a T instead of an elbow below the valve?

I think the barrel support and the piston could be made much lighter, I suggest to improve that to complete a very well built gun.
Keep up the good work! :D
Till the day I'm dieing, I'll keep them spuddies flying, 'cause I can!

Spudfiles steam group, join!
User avatar
VH_man
Staff Sergeant 4
Staff Sergeant 4
Posts: 1827
Joined: Sat Dec 09, 2006 6:00 pm
Location: New Hampshire
Been thanked: 1 time

Thu Oct 15, 2009 5:31 am

My only complaint is that the hollowed out portion of your piston is increasing pilot volume. Fill the hole in with something light but airtight, Like a mix of cheerios (or Styrofoam if you must use legitimate building materials) and epoxy.

also, whats that hole in the side of the piston for? It seems to me that it's decreasing your power immensely. It looks as if its an Equalization hole, which is unnecessary if you dont have O-rings sealing the piston.

Finally, After constructive criticism.... Very nice gun. It looks very clean and professional, and i'm sure will be amazingly fun at the higher pressure ranges. That and I envy your machining abilities. Ive always wanted to make a piston valve as gorgeous as this...
User avatar
tghhs
Specialist
Specialist
Posts: 176
Joined: Wed Dec 31, 2008 11:01 pm

Thu Oct 15, 2009 6:01 am

WOW! thats sweet man, yeah awesome machining work, is the piston steel? It's been said, just try and lighten it as much as possible.
User avatar
Jack_Hogg
Specialist
Specialist
Posts: 133
Joined: Tue Feb 20, 2007 7:56 am

Thu Oct 15, 2009 6:34 am

VH_man wrote:also, whats that hole in the side of the piston for? It seems to me that it's decreasing your power immensely. It looks as if its an Equalization hole, which is unnecessary if you dont have O-rings sealing the piston...
I have just tested the piston today, and it preforms.., well... kinda slow.. :cry: I think I have to fill up the hole.. but my next question is, will air, flow around the piston quickly enough to fill up the air chamber?
also, whats that hole in the side of the piston for? It seems to me that it's decreasing your power immensely. It looks as if its an Equalization hole, which is unnecessary if you dont have O-rings sealing the piston.
I will fill up the hole with some epoxy i think... U are right about decreasing power immensely. Thanks for the tip.
tghhs wrote:WOW! thats sweet man, yeah awesome machining work, is the piston steel? It's been said, just try and lighten it as much as possible.
Thanks mate :) The piston is made of aluminium.
psycix wrote:Why is there a T instead of an elbow below the valve
Just for the looks:)
User avatar
auxiliary
Specialist
Specialist
Posts: 145
Joined: Sun Jan 20, 2008 12:01 pm
Been thanked: 1 time

Thu Oct 15, 2009 8:50 am

The piston will allow enough airflow for filling without the hole as long as it isn't extremely tight in the housing like hydraulic tube.
User avatar
jmadden91
Specialist 2
Specialist 2
Posts: 246
Joined: Thu May 07, 2009 6:03 pm
Location: Queensland, Australia

Thu Oct 15, 2009 9:52 am

Wow mate it is absolutely gorgeous congratulations.

One reason the piston may be underperforming is the way the pilot is being vented through the male quick connect, it looks like it may be choking the flow a bit perhaps?

Congrats again mate :thumbleft:
User avatar
Mitchza89
Sergeant
Sergeant
Posts: 1056
Joined: Tue Jan 09, 2007 12:05 am

Thu Oct 15, 2009 10:08 am

That's one of the best looking guns I've seen for a while. Fantastic work there mate. As far as performance goes.... Your piston looks beautifully machined but the equalization hole is way too big. The reason your performance isn't too good is because of the combination of that hole and the compressor quick connect. The ball valve is more then big enough to pilot the gun but that quick connect is constricting how fast it can pilot. It doesn't help that the equalization hole is nearly the same size. All the pressurized air is going out straight out that hole and through the quick connect fitting.

Keep up the great work and I hope everyone's information helps you :)



EDIT.... I should have read what you said first Mr Madden :D
Nice to see we're on the same page though hehe
Image
User avatar
Jack_Hogg
Specialist
Specialist
Posts: 133
Joined: Tue Feb 20, 2007 7:56 am

Thu Oct 15, 2009 10:47 am

Ok thanks for nice comments :) So, how should I add a quick connect without the male side? Or perhaps a bigger male quick connect? (those short thick male connects) Maybe that will fix the problem? (including the fact that I will fill up the piston with some hot glue) :roll:

And if all those problems are fixed, including the fact that I still need an fridgecompressor (getting one soon for free), well then I think I am going to solder brass iron sights (rear sight on the T-piece, and front sight offcourse on the barrel itself). And I am thinking of adding a good grip, like cordwrapping the handle or perhaps a rubber heatshrink. Also, the ballvalve is a bit stiff, how do I get the ballvalve looser? (piloting smoother) Thanks for the help people :P
User avatar
psycix
Sergeant Major 4
Sergeant Major 4
Posts: 3684
Joined: Mon Jun 25, 2007 7:12 am
Location: The Netherlands

Donating Members

Thu Oct 15, 2009 12:37 pm

how do I get the ballvalve looser
That's how ball valves are. Its because of the seal.
Some oiling helps a bit, and chucking the rod into a drill, spinning the hell out of it may also loosen it somewhat. It may help a bit, but a ballvalve will always be stiff.

I don't think the male quick connect is much of a problem. The heavy piston in combination with the hole is.
Till the day I'm dieing, I'll keep them spuddies flying, 'cause I can!

Spudfiles steam group, join!
User avatar
Brian the brain
Moderator
Moderator
Netherlands
Posts: 3496
Joined: Mon Dec 05, 2005 2:06 am
Location: Holland
Been thanked: 3 times

Thu Oct 15, 2009 4:12 pm

One reason the piston may be underperforming is the way the pilot is being vented through the male quick connect, it looks like it may be choking the flow a bit


NOOO!!
Image
works fine!
So does Psy's
Image
And even with an empty schrader:

Image
No problem piloting.

The problem is blowby and piston weight.Also, a gun like Jack's should be fired at pressures over 300 PSI..

Anyone for calling this type of design a Dutchy?

I made several, Psycix has one, TNW has one and now another Dutch spudder.

I have to say this one is the prettiest "copy" so far.
I love the stacked Tees..I only did that on my first version , also for looks, and I must say...it rocks!

I love the trigger, very well done!

If I hadn't made mark III ( TOP PICTURE) recently I'd be pretty pissed :D
Almost got beaten at my own game..
It is most similar to my first one but way better..

You might want to try a 28 mm copper barrel and some big 1" marbles ( bonken)..you will be amazed...
Gun Freak wrote:
Oh my friggin god stop being so awesome, that thing is pure kick ass. Most innovative and creative pneumatic that the files have ever come by!

Can't ask for a better compliment!!
User avatar
Mitchza89
Sergeant
Sergeant
Posts: 1056
Joined: Tue Jan 09, 2007 12:05 am

Thu Oct 15, 2009 7:19 pm

Dutchy sounds good. Funny though, I've made many many guns that have that exact design and my mums side is dutch :D

Ironic..
Image
User avatar
Jack_Hogg
Specialist
Specialist
Posts: 133
Joined: Tue Feb 20, 2007 7:56 am

Fri Oct 16, 2009 4:01 am

Ok, psycix. So can you make a drawing (scetch) how I should make the piston? That would be great, only today, becouse tomorrow it's a week off so I don't have a lathe.. you nkow.. :wink:
User avatar
Crna Legija
First Sergeant 2
First Sergeant 2
Posts: 2333
Joined: Sun Jul 20, 2008 5:14 am
Location: australia

Fri Oct 16, 2009 4:41 am

Don't fill the hole piston with hot glue, is better to fill it with a light foam and hold it in with epoxy. it will keep it light and still have lower pilot.if you make a new piston try UHMW,teflon,Nylon or delrin to make it even lighter
'' To alcohol... The cause of, and solution to, all of life's problems.”
--Homer Simpson

Add me on ps3: wannafuk, 8/11/11 cant wait
User avatar
Jack_Hogg
Specialist
Specialist
Posts: 133
Joined: Tue Feb 20, 2007 7:56 am

Fri Oct 16, 2009 9:53 am

Well, too late, I already have changed the piston now, and preformance is a little bit better, but not how I like it, well the results are

1. Testing with first version was like psssssstPOW
2. Testing second version was like pssstPOW
3. Testing 3rd version was like psstPOW
4. Testing 3rd version with lube was like psssssssssstPOW
All tests were at 180PSI

So I was using model steam engine oil as lubricant. If I don't use lube on the 3rd version, I have best preformance but not good enough.. The second version was just like the first version but with the rod screwed in.

So here it is:
Image
Image
Image
Image
Image
Post Reply