Piston length ?

Show us your pneumatic spud gun! Discuss pneumatic (compressed gas) powered potato guns and related accessories. Valve types, actuation, pipe, materials, fittings, compressors, safety, gas choices, and more.
c9d
Private 3
Private 3
Posts: 44
Joined: Sun Nov 04, 2007 12:56 am

Thu May 13, 2010 11:29 pm

I am making a 3" piston for a coaxial setup and was wondering if the length of the piston mattered? My pistons overall length currently is 2" from front to back.
User avatar
deathbyDWV
Corporal
Corporal
Posts: 576
Joined: Sat May 16, 2009 4:02 pm
Location: Owasso, OK

Thu May 13, 2010 11:43 pm

I would suggest having the piston at least as long as the diamater of the pipe it's sliding in to make sure it doesn't get jammed. Otherwise, it will could slip crooked when pressurized or piloted and jam... Although, as long as it's lubricated good and fits correctly it will probably still work...
Life's too short to mark off the items on your wish list...
User avatar
Gippeto
First Sergeant 3
First Sergeant 3
Venezuela
Posts: 2503
Joined: Sat Jan 19, 2008 10:14 am
Location: Soon to be socialist shit hole.
Has thanked: 2 times
Been thanked: 17 times

Donating Members

Thu May 13, 2010 11:49 pm

Could be a huge topic to delve into details, this vs that, etc. ...It's sufficient to say "It'll work fine at 2" length." :)


Edit: If the piston is a sloppy enough fit that jamming becomes a real issue...it's FAR too sloppy of a fit to work anyway. :wink:
"It could be that the purpose of your life is to serve as a warning to others" – unknown

Liberalism is a mental disorder, reality is it's cure.
c9d
Private 3
Private 3
Posts: 44
Joined: Sun Nov 04, 2007 12:56 am

Fri May 14, 2010 12:07 am

@Gipetto I tried to go with your sealing piston idea you suggested to me before. I will try to get some pics up when I finish it.
User avatar
Gippeto
First Sergeant 3
First Sergeant 3
Venezuela
Posts: 2503
Joined: Sat Jan 19, 2008 10:14 am
Location: Soon to be socialist shit hole.
Has thanked: 2 times
Been thanked: 17 times

Donating Members

Fri May 14, 2010 12:44 am

The u-cup? That'll work nicely I'm thinking. :D
"It could be that the purpose of your life is to serve as a warning to others" – unknown

Liberalism is a mental disorder, reality is it's cure.
c9d
Private 3
Private 3
Posts: 44
Joined: Sun Nov 04, 2007 12:56 am

Fri May 14, 2010 12:49 am

Its not exactly a "u cup seal", but as close to it I can get using stuff from the hardware store.
User avatar
mark.f
Sergeant Major 4
Sergeant Major 4
Eritrea
Posts: 3627
Joined: Sat May 06, 2006 11:18 am
Location: The Big Steezy
Has thanked: 52 times
Been thanked: 53 times
Contact:

Donating Members

Fri May 14, 2010 7:25 am

Well, here's a simple way to do it...

Measure the distance from the back of your barrel to the front of your plug/cap/bushing/etc. that closes off the back of the launcher.

Take that distance, subtract your bumper length (when compressed if it is foamy) and your desired opening distance. This will give you the overall length your piston should be.

Extremely simple.

Now, if your gun isn't built yet, this gives you the opportunity to adjust your piston length to reduce weight. Like deathbyDWV said, make it long enough so that it doesn't jam, then add your bumper length and opening distance to the piston, and adjust how far your barrel goes back into the launcher accordingly.
User avatar
Technician1002
Captain
Captain
Posts: 5189
Joined: Sat Apr 04, 2009 11:10 am

Fri May 14, 2010 11:43 am

The shorter the length the less mass. Shorter is better with that yardstick.

Longer gives more area to align it and more area to provide a seal. Longer is better with that yardstick.

A good balance is somewhere in between. Short to be light and long enough to keep alignment and seal in the sleeve it retracts into. There is no law stating the piston must be longer than it's diameter.

A traditional piston makes a barrel seal on it's face, where a QDV (spool valve) makes seals on the side. As such a QDV will use a longer heavier piston than is necessary for a traditional piston valve.

Many commercial piston valves have the piston length well below 1/2 the diameter. This includes the Martin Blaster valves (commercial hopper blasters) and QEV's.

For ease of building with common home tools, a longer pistion is often built to overcome the precision requirements of short pistons. There is nothing wrong with this trade-off. Build it so it works is rule number one.
User avatar
john bunsenburner
Sergeant 5
Sergeant 5
Posts: 1446
Joined: Sun Oct 19, 2008 5:13 am

Fri May 14, 2010 2:00 pm

It is funny no one mentioned it but: For a given pilot volume(without the piston) a larger piston will decrease the amount of air vented, and also decreases the piston travel. Thus if you have a gun built already a longer piston may just be preferable to a shorter one.

(The above is a hypothesis and is not based on any sound evidence, if my reasoning is faulty please tell me so)
"Did you ever stop to think that out of the seven deadly sins envy is the only one which doesn't give the sinner even momentary pleasure"-George Will
c9d
Private 3
Private 3
Posts: 44
Joined: Sun Nov 04, 2007 12:56 am

Sat May 15, 2010 10:27 pm

What would you guys recommend to lubricate this piston? Something that doesnt affect PVC or destroy rubber
User avatar
Gun Freak
Lieutenant 5
Lieutenant 5
Posts: 4971
Joined: Mon Jan 25, 2010 4:38 pm
Location: Florida
Been thanked: 7 times

Sat May 15, 2010 10:54 pm

I use vaseline.
OG Anti-Hybrid
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna"M16 BBMGPengunHammer Valve Airsoft SniperHigh Pressure .22 Coax
Holy Shat!
User avatar
Gippeto
First Sergeant 3
First Sergeant 3
Venezuela
Posts: 2503
Joined: Sat Jan 19, 2008 10:14 am
Location: Soon to be socialist shit hole.
Has thanked: 2 times
Been thanked: 17 times

Donating Members

Sat May 15, 2010 11:56 pm

I've been using MolyKote 55 on my builds. It's silicone based, and pretty much non reactive. It does swell buna o-rings slightly, but hasn't caused any problems thus far.

Other silicone based lubes are available at auto parts stores...dielectric grease being one....a bit on the thick side, but a "dab 'l do ya". :)

Pretty sure the disc brake caliper lube is also silicone based.
"It could be that the purpose of your life is to serve as a warning to others" – unknown

Liberalism is a mental disorder, reality is it's cure.
User avatar
Technician1002
Captain
Captain
Posts: 5189
Joined: Sat Apr 04, 2009 11:10 am

Sun May 16, 2010 1:28 am

With the plastics an plumbing o rings I use, I use either a plumbing grease or white lithium grease.
Slauma
Private 3
Private 3
Posts: 46
Joined: Sun Dec 20, 2009 12:28 pm

Sun May 16, 2010 11:44 pm

I use lithium grease as well. From what I've read and seen it plays nicely with all of the most common construction materials used in spudding; pvc, cpvc, abs, metals, o-rings of various material
TheLostOtter
Private
Private
Posts: 7
Joined: Thu Aug 06, 2009 1:18 am

Mon May 17, 2010 1:47 am

I'm using a 3" ABS endcap inside a 4" PVC chamber for my coaxial cannon. Very reliable and the piston is pretty much a chode lol, maybe 2.5" long and 3.5" diameter. I used a few coats of black rubberized spray paint to get it to seal better. It's still wasn't a perfect fit but the thing shoots so hard I'll just assume it can't get much better.

And I'm using vegetable oil to lube the thing. Didn't want to use anything that would react with the PVC so I figured that would be my safest bet using something I already had at home.
Post Reply