DWV
- Lockednloaded
- Staff Sergeant
- Posts: 1566
- Joined: Thu Sep 03, 2009 9:38 pm
- Location: Texas, USA
- Been thanked: 6 times
DWV, or Drain, Waste, and Venting fittings are notorious in this forum for being dangerous and just plain stupid to use on any pneumatic cannon. DWV nazis jump on every thread containing any DWV on a cannon, but is it really that dangerous when used correctly?
There are countless amateur cannons that use DWV fittings at low pressures (~80 psi) that are all over youtube and instructables, and even on our own site advanced combustions capable of pressure spikes up to, IIRC, 120psi. Most failures I've seen in recent years seem to be bad irrigation pipe, or cannons just put together poorly. I know it seems that even if doesn't happen to them it doesn't mean it can't happen to you, but there are just so many DWV cannons that have never exploded.
I went to a friend's ranch this weekend where they had an amateur ball valve spudgun. It had a 4" to 2" bell reducer, so I warned them about how dangerous this cannon was. They told me that they had regularly taken it up to 120 psi for three years, a pressure I might not even take pressure rated 4" PVC.
This is just a thought, shoot it down if you like. I'm just looking at the facts in front of me...
There are countless amateur cannons that use DWV fittings at low pressures (~80 psi) that are all over youtube and instructables, and even on our own site advanced combustions capable of pressure spikes up to, IIRC, 120psi. Most failures I've seen in recent years seem to be bad irrigation pipe, or cannons just put together poorly. I know it seems that even if doesn't happen to them it doesn't mean it can't happen to you, but there are just so many DWV cannons that have never exploded.
I went to a friend's ranch this weekend where they had an amateur ball valve spudgun. It had a 4" to 2" bell reducer, so I warned them about how dangerous this cannon was. They told me that they had regularly taken it up to 120 psi for three years, a pressure I might not even take pressure rated 4" PVC.
This is just a thought, shoot it down if you like. I'm just looking at the facts in front of me...
I love lamp
- inonickname
- First Sergeant 4
- Posts: 2606
- Joined: Sun Dec 07, 2008 3:27 am
There's really no need to tempt fate. In some applications it's riskier than others.
Some kewls also spend years making TATP, while some lose fingers on their first go. There's a lot of factors involved.
Some kewls also spend years making TATP, while some lose fingers on their first go. There's a lot of factors involved.
PimpAssasinG wrote:no im strong but you are a fat gay mother sucker that gets raped by black man for fun
- Technician1002
- Captain
- Posts: 5189
- Joined: Sat Apr 04, 2009 11:10 am
I found there is a difference between ABS and PVC DWV. The failure mode is important in safety. PVC is brittle.
I have broken PVC parts, but not ABS.
I have broken PVC parts, but not ABS.
- Lockednloaded
- Staff Sergeant
- Posts: 1566
- Joined: Thu Sep 03, 2009 9:38 pm
- Location: Texas, USA
- Been thanked: 6 times
The issue with DWV has never been exploding PVC, its usually socket depth and fittings popping off
I love lamp
- Crna Legija
- First Sergeant 2
- Posts: 2333
- Joined: Sun Jul 20, 2008 5:14 am
- Location: australia
the big problem is if you drop it full when it pressurised and explodes sending pvc shards all over the place
'' To alcohol... The cause of, and solution to, all of life's problems.”
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
- inonickname
- First Sergeant 4
- Posts: 2606
- Joined: Sun Dec 07, 2008 3:27 am
I rarely use PVC in the construction of my cannons, but I'd consider this to be a problem with any brittle, plastic, pressurized vessel.-_- wrote:the big problem is if you drop it full when it pressurised and explodes sending pvc shards all over the place
PimpAssasinG wrote:no im strong but you are a fat gay mother sucker that gets raped by black man for fun
- Crna Legija
- First Sergeant 2
- Posts: 2333
- Joined: Sun Jul 20, 2008 5:14 am
- Location: australia
Well yea but pvc is the most commonly use brittle plastic around here.
Dam i should be on your list, reread my post and its bad
Dam i should be on your list, reread my post and its bad
'' To alcohol... The cause of, and solution to, all of life's problems.”
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
DWV can be safe, but so is driving a car without a seatbelt, crashing is unlikely, but when you do, you're stuffed.
I don't use plastic in most things, size being the only limit.
ABS seems safer, as was mentioned above, due to the potential failure modes.
I think most of belong on that list at some point.
I don't use plastic in most things, size being the only limit.
ABS seems safer, as was mentioned above, due to the potential failure modes.
I think most of belong on that list at some point.
-
- First Sergeant 3
- Posts: 2400
- Joined: Wed Oct 18, 2006 11:12 pm
- Has thanked: 2 times
- Been thanked: 10 times
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.
Last edited by SpudBlaster15 on Thu Jul 15, 2021 1:57 am, edited 1 time in total.
- Lockednloaded
- Staff Sergeant
- Posts: 1566
- Joined: Thu Sep 03, 2009 9:38 pm
- Location: Texas, USA
- Been thanked: 6 times
I know people hate PVC because of it horribly dangerous "failure mode", but this thread isn't just to bash on PVC, its to discuss a sub-section of PVC fittings known a DWV. all arguments saying normal PRESSURE Rated PVC is bad in the first place are irrelevant to this thread. I just want to discuss the shortcomings of DWV fittings; not the material they are made of
I love lamp
my first cannon was a dwv one and i didn't notice until the nazi's jumped on my case. however i dare not take it above 70 although i once took it to 120 covered in heavy cloth before exhausting it just to protect myself from a possible explosion. i still use it but not as much as my newest cannon. i would use pressure rated pipe just to be on the safe side but if you have a dwv cannon i recommend taking it as high as you are willing to take it at first covered in cloth, but then lower the psi by about 20 just to be on the safe side.
- Lockednloaded
- Staff Sergeant
- Posts: 1566
- Joined: Thu Sep 03, 2009 9:38 pm
- Location: Texas, USA
- Been thanked: 6 times
The cloth will not help, PVC shrapnel will tear through it like nothing is even there, but I'm glad you don't take your cannon to those pressures on a regular basis
I love lamp
- Crna Legija
- First Sergeant 2
- Posts: 2333
- Joined: Sun Jul 20, 2008 5:14 am
- Location: australia
dwv fittings are just as bad, they have short socket depth.
'' To alcohol... The cause of, and solution to, all of life's problems.”
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
--Homer Simpson
Add me on ps3: wannafuk, 8/11/11 cant wait
- Fnord
- First Sergeant 2
- Posts: 2239
- Joined: Tue Feb 13, 2007 9:20 pm
- Location: Pripyat
- Been thanked: 1 time
- Contact:
Also, some dwv fitting are considerably thinner, or not contoured correctly for pressure safety(such as large end caps).
I woundn't worry too much about <2" diameter fittings, though, if you know how to solvent weld properly.
And I doubt pvc shrapnel has a high fatality rate with 80psi behind it, but a full-face shield is necessary. edit: Also hearing protection, if you value it as much as I do.
I woundn't worry too much about <2" diameter fittings, though, if you know how to solvent weld properly.
And I doubt pvc shrapnel has a high fatality rate with 80psi behind it, but a full-face shield is necessary. edit: Also hearing protection, if you value it as much as I do.
Last edited by Fnord on Tue Aug 17, 2010 10:01 am, edited 1 time in total.
- Lockednloaded
- Staff Sergeant
- Posts: 1566
- Joined: Thu Sep 03, 2009 9:38 pm
- Location: Texas, USA
- Been thanked: 6 times
I have sch 40 DWV PVC fittings at all my hardware stores. Since sch 40 referes to wall thickness, I'll be without any PVC shrapnel anywhere in my body
I am refering to large diameter fittings; I can get pressure rated fittings up to 2"
I am refering to large diameter fittings; I can get pressure rated fittings up to 2"
I love lamp