QEV QE-03
-
AircannonSweden
- Specialist
- Posts: 131
- Joined: Thu Oct 27, 2011 11:53 am
- Location: Sweden,Linköping
Okey,so i bought this today: http://www.ebay.com/itm/G3-8-Pipe-Pneum ... 849wt_1270 is the quality good on it?what do you guys think?
-
pipeboyswe
- Private 3
- Posts: 40
- Joined: Tue Sep 01, 2009 8:52 am
- Location: Sweden
It will do the job just fine, seen that kind of QEVs on other guns here. Just dont use too high pressure since its not rated for any high pressure ( i wouldent feel safe using it over 250psi 
) Nice too see other sweds here 
) Nice too see other sweds here -
AircannonSweden
- Specialist
- Posts: 131
- Joined: Thu Oct 27, 2011 11:53 am
- Location: Sweden,Linköping
Yeeeeah Swedenpipeboyswe wrote:It will do the job just fine, seen that kind of QEVs on other guns here. Just dont use too high pressure since its not rated for any high pressure ( i wouldent feel safe using it over 250psi
.the valve is rated for 10 bars ))-
jakethebeast
- Corporal 5
- Posts: 945
- Joined: Sat Jul 03, 2010 4:20 pm
- Location: Jakes cave
phyh, sweden, FINLAND FTW!
But enough with this morking, if i remember correctly, JSR made semi-auto using this exact kind of QEV
But enough with this morking, if i remember correctly, JSR made semi-auto using this exact kind of QEV
Est Sularus Oth Mithas
-
jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
AircannonSweden
- Specialist
- Posts: 131
- Joined: Thu Oct 27, 2011 11:53 am
- Location: Sweden,Linköping
Okey,i got the valve today i are a bit confused so help med please:)
"A",should the airchamber go there?
"R",the barrel?
"P",the blowgun?
I NEED HELP PLEASE?:)
i are a bit confused so help med please:)"A",should the airchamber go there?
"R",the barrel?
"P",the blowgun?
I NEED HELP PLEASE?:)
-
Goats spudz
- Specialist 4
- Posts: 458
- Joined: Tue Aug 02, 2011 12:31 pm
- Contact:
Correct !AircannonSweden wrote:Okey,i got the valve today
"A",should the airchamber go there?
"R",the barrel?
"P",the blowgun?
I NEED HELP PLEASE?:)
A = Air Chamber
R = Release
P = Pilot
Where's my Chuck key?
-
AircannonSweden
- Specialist
- Posts: 131
- Joined: Thu Oct 27, 2011 11:53 am
- Location: Sweden,Linköping
thank you:)Goats spudz wrote:Correct !AircannonSweden wrote:Okey,i got the valve today
"A",should the airchamber go there?
"R",the barrel?
"P",the blowgun?
I NEED HELP PLEASE?:)
A = Air Chamber
R = Release
P = Pilot
-
jackssmirkingrevenge
- Five Star General
- Posts: 26216
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 576 times
- Been thanked: 347 times
... had you read the thread I linked to:
"P" denotes the pilot port, where the slide valve should be attached. Your air supply/main chamber should then be attached to the other end of the slide valve. In this case I hooked it up directly to my compressor. This port is compatible with 1/4" BSP.
"A" is where the firing chamber should be attached. For each shot, all the air that is in this chamber will be emptied. In this case I made a small chamber from a section of PVC pipe with epoxy endcaps, with a 1/4" socket screwed into one end to attach to the QEV. This port is compatible with 1/4" BSP.
"R" is where the barrel or magazine should be attached. This port is compatible with 3/8" BSP.
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
AircannonSweden
- Specialist
- Posts: 131
- Joined: Thu Oct 27, 2011 11:53 am
- Location: Sweden,Linköping
Yes i have read it:)jackssmirkingrevenge wrote:... had you read the thread I linked to:
"P" denotes the pilot port, where the slide valve should be attached. Your air supply/main chamber should then be attached to the other end of the slide valve. In this case I hooked it up directly to my compressor. This port is compatible with 1/4" BSP.
"A" is where the firing chamber should be attached. For each shot, all the air that is in this chamber will be emptied. In this case I made a small chamber from a section of PVC pipe with epoxy endcaps, with a 1/4" socket screwed into one end to attach to the QEV. This port is compatible with 1/4" BSP.
"R" is where the barrel or magazine should be attached. This port is compatible with 3/8" BSP.