Ok so I received my qev and my shock pump. I was very excited to build my air rifle so I went out and bought all the parts, Pink teflon tape(stronger than the white) and taped up the threads, screwed it all together and I went to go pump it up and... It leaks! Not the gun the shock pump!!! Its brand new I have been trying to fix the leak for a week! it looks like this
http://www.google.com/imgres?um=1&hl=en ... 2,s:0,i:88
It leaks out of where the hose connects to the pump. I tried screwing it on tighter and that didn't work. I tried putting Teflon tape on the thread and that didn't work I was messing around with it for over an hour and it wont stop leaking anyone got some tips???
seriously need help.
-
jackssmirkingrevenge
- Five Star General
- Posts: 26179
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 543 times
- Been thanked: 321 times
silly question, did you tighten the red knob as well?
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
beastmode986
- Specialist
- Posts: 170
- Joined: Sat Mar 03, 2012 11:13 am
I mean where the hose scres onto the pump body. I know how to use the pump and yes i tightened everything down.
-
jackssmirkingrevenge
- Five Star General
- Posts: 26179
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 543 times
- Been thanked: 321 times
are there any dents on the upper surface of the schrader valve?
could you take a good (
) photo of the seal on the pump head and the schrader valve?
could you take a good (
) photo of the seal on the pump head and the schrader valve?hectmarr wrote:You have to make many weapons, because this field is long and short life
-
PotatoEnemy17
- Specialist
- Posts: 100
- Joined: Tue Apr 10, 2012 6:33 pm
Is it possible that there is a bleed valve, like on high pressure pumps?
-
beastmode986
- Specialist
- Posts: 170
- Joined: Sat Mar 03, 2012 11:13 am
it leaks out of there. Either the hose it self or where the brass piece screws on.
-
jackssmirkingrevenge
- Five Star General
- Posts: 26179
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 543 times
- Been thanked: 321 times
have you removed the hose to see if the o-ring is intact?
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
Mr.Tallahassee
- Specialist 3
- Posts: 364
- Joined: Sun Jul 10, 2011 2:35 am
Check it with soapy water while pumping. That will tell you where the leak is from.
Sarcasm is the body's natural defense against stupid.
Petitlu wrote:My balls are made of lead and weigh 22g but I can make heavier or lighter ...
-
jackssmirkingrevenge
- Five Star General
- Posts: 26179
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 543 times
- Been thanked: 321 times
It could be improperly crimped...
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
beastmode986
- Specialist
- Posts: 170
- Joined: Sat Mar 03, 2012 11:13 am
well if it is then how can I fix that?
-
jackssmirkingrevenge
- Five Star General
- Posts: 26179
- Joined: Thu Mar 15, 2007 11:28 pm
- Has thanked: 543 times
- Been thanked: 321 times
Moar crimping! Probably with pliers 
That or epoxy. Or and epoxy.
That or epoxy. Or and epoxy.
hectmarr wrote:You have to make many weapons, because this field is long and short life
-
PotatoEnemy17
- Specialist
- Posts: 100
- Joined: Tue Apr 10, 2012 6:33 pm
@beastmode986 You should know, if you ask JSR a question your going to need epoxy - lots of epoxy. Not that I'm against epoxy... 
Not that I'm against epoxy...