Custom Aluminum Pneumatic Build

Show us your pneumatic spud gun! Discuss pneumatic (compressed gas) powered potato guns and related accessories. Valve types, actuation, pipe, materials, fittings, compressors, safety, gas choices, and more.
User avatar
gyrotech
Private 3
Private 3
Posts: 55
Joined: Fri Sep 28, 2012 5:32 pm

Thu May 16, 2013 9:08 pm

Piston Valve piloted by a QEV. Golf Ball Sized Barrel. So far all aluminum but we shall see what happens when I get to the chamber.

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Lots more work to go. I have roughly 8 hours into machining so far. Stay tuned folks :)
millons70
Private 2
Private 2
Posts: 36
Joined: Wed Apr 03, 2013 9:02 pm

Thu May 16, 2013 9:45 pm

Great work, lucky you have access to tools to make that!

Very clean work too BTW
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Thu May 16, 2013 11:38 pm

You've made my Sherline feel very small :)

Excellent work, please tell me this is destined for HPA!
hectmarr wrote:You have to make many weapons, because this field is long and short life
User avatar
Crna Legija
First Sergeant 2
First Sergeant 2
Posts: 2333
Joined: Sun Jul 20, 2008 5:14 am
Location: australia

Fri May 17, 2013 3:03 am

nice work sure will be a performer!
jackssmirkingrevenge wrote:You've made my Sherline feel very small

I went to an engineering expo last thursday there was a lathe on show that had 17 meters between centers and 3.5meter swing no tail sock had two spindles and 3 steady rests! yet made no more noise at 3000 rpm then the 40'' 120'' at work.
'' To alcohol... The cause of, and solution to, all of life's problems.”
--Homer Simpson

Add me on ps3: wannafuk, 8/11/11 cant wait
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Fri May 17, 2013 3:06 am

Image

A man can dream :D
hectmarr wrote:You have to make many weapons, because this field is long and short life
User avatar
Crna Legija
First Sergeant 2
First Sergeant 2
Posts: 2333
Joined: Sun Jul 20, 2008 5:14 am
Location: australia

Fri May 17, 2013 3:14 am

hahah lol once you're in canada you can just print your own :)
'' To alcohol... The cause of, and solution to, all of life's problems.”
--Homer Simpson

Add me on ps3: wannafuk, 8/11/11 cant wait
User avatar
Kilash
Private 4
Private 4
Posts: 70
Joined: Thu Jan 21, 2010 12:20 am

Fri May 17, 2013 9:28 am

That is some nice aluminum work :o .
User avatar
Hubb
First Sergeant 2
First Sergeant 2
Posts: 2390
Joined: Mon May 28, 2007 8:39 am
Location: South Georgia
Contact:

Fri May 17, 2013 6:18 pm

I almost said a "non-forum approved word". Nice work and looking forward to the finished product.
User avatar
Solar
Corporal
Corporal
United States of America
Posts: 545
Joined: Tue May 17, 2005 11:53 pm
Has thanked: 1 time
Been thanked: 17 times

Sat May 18, 2013 5:45 am

The chamber would be good in aluminum too. What other materials are you considering?
User avatar
gyrotech
Private 3
Private 3
Posts: 55
Joined: Fri Sep 28, 2012 5:32 pm

Sat May 18, 2013 8:30 am

I'm considering 304 Stainless Steel or 6160 Aluminum for the Chamber. The valve body is 6160 Aluminum. I may consider Mild Steel for the chamber if I can find a nice enough prebuilt air peg. Modify with larger ports. Everything must look Pretty :)

I made a piston out of Acetal but it's pretty heavy. I might make the piston from Aluminum, hollow it out, weld a cap on one end.
User avatar
velocity3x
Corporal 4
Corporal 4
Posts: 828
Joined: Fri Jun 05, 2009 3:09 pm
Location: Yuma, Arizona
Contact:

Sat May 18, 2013 12:23 pm

gyrotech,
Absolutely beautiful work! What operating pressure do you plan to use? What are you using for a piston / barrel seal?
User avatar
ramses
Staff Sergeant 2
Staff Sergeant 2
United States of America
Posts: 1679
Joined: Thu May 29, 2008 6:50 pm

Sat May 18, 2013 10:15 pm

That does look amazing. How long did it take you to bore the thin walled piece on the lathe? Or did you use a very large drill bit to take it most of the way?
POLAND_SPUD wrote:even if there was no link I'd know it's a bot because of female name :D
User avatar
gyrotech
Private 3
Private 3
Posts: 55
Joined: Fri Sep 28, 2012 5:32 pm

Sat May 18, 2013 11:24 pm

velocity3x wrote:gyrotech,
Absolutely beautiful work! What operating pressure do you plan to use? What are you using for a piston / barrel seal?
Not to concerned about higher pressures. I have a Viair 450c air compressor, setup to use in my truck. Top's about 150psi. I'm planning a long barrel, 6 or 7 feet. With a C:B ratio of 3:1.

The piston was going to be a piece of machined Acetal, which is a hard plastic basically. I'm switching that up for hollow aluminum. Should be very light. It is barrel seal. Most people use rubber for the seal? I have some nice gasket material at work. Might try that. I'm also planning on a rubber bumper for the piston to slam into. I imagine it would take quite a hit without one.

I do plan to water pressure test the unit. This gun will be used around family, friends. I plan to test at 300psi maybe more for a very large safety factor.

If your familiar with water pressure testing, basically you fill with water, then add air pressure. Water being virtually incompressible, not much can go wrong if it fails on testing. Also leaks are easily spotted. Although I doubt I'll have any leaks.
ramses wrote:That does look amazing. How long did it take you to bore the thin walled piece on the lathe? Or did you use a very large drill bit to take it most of the way?
The third picture shows the holes I drilled. I used a boring bar to then enlarge the holes. I started with a 1.5" drill bit. Generally I did 0.200"-0.300" passes for rough cuts and 0.050" for final cuts. I would not call myself a machinist. I did not go to school for machining. I am a welder, a fitter, a lead hand. I build food handling equipment and have picked up a fair bit of skills along the way. I do not know how to calculate proper travel speeds for cutting...however I do understand whats to fast, to slow, I can make a slip fit accurate to a few thousandths of an inch or a nice press fit.

I have about 8 hours of machining into the project so far. To me, that's working pretty fast.
User avatar
gyrotech
Private 3
Private 3
Posts: 55
Joined: Fri Sep 28, 2012 5:32 pm

Sat May 18, 2013 11:32 pm

Thanks for the possitive comments guys :)
User avatar
gyrotech
Private 3
Private 3
Posts: 55
Joined: Fri Sep 28, 2012 5:32 pm

Sat May 18, 2013 11:34 pm

jackssmirkingrevenge wrote:You've made my Sherline feel very small :)

Excellent work, please tell me this is destined for HPA!
Not sure what HPA is?
Post Reply