Small Pneumatic Launcher Help

Show us your pneumatic spud gun! Discuss pneumatic (compressed gas) powered potato guns and related accessories. Valve types, actuation, pipe, materials, fittings, compressors, safety, gas choices, and more.
Genadmm
Private
Private
Posts: 3
Joined: Wed Mar 20, 2019 11:35 pm

Fri Mar 22, 2019 10:07 pm

Greetings, :D
This is my fist post on this forum and I'm pretty new to it all. I am currently planning to make a small pneumatic line launcher that can launch roughly a 1 to 2 lb (.45kg to .9kg) projectile with a pretty light kevlar line approximately 45 feet (13.7meters) . Ideally the entirety of the launcher would not be longer than 8 inches. I'm looking for some advice and general suggestions.

Initial Design Plan :idea:
Finding this forum gave me a great amount of archives to look through and plenty of designs to begin with. My initial idea was to utilize a QEV design with a small footprint. The projectile would sleeve over the barrel rather than a traditional "muzzle loaded" approach. I would like to use Co2 cartridges possibly 12 to 20 gram as the main air source rather than a conventional air compressor. With some of the QEV designs I've looked at they tend to utilize a mechanical triggering system ( ball valve, air gun trigger, exhaust hand slide valves, etc) I would like to use a solenoid or have a way of having the qev triggered with the means of electrical switch.

Questions :?:
With the design thought out a bit, it just leaves me wondering how to correctly calculate the specifics of the design.How much stored pressure would be needed to meet the requirements? What size Co2 cartridge should I use? How much pressure can be generated with just the Co2 cartridges? These are just a few questions that I have but I think it would be best to just get this idea out there first and get some feedback from the Spud Community.

Thanks,
-Bausomer
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Sun Mar 24, 2019 5:32 am

Welcome to the forum!

The first suggestion would be to master the use of Gas Gun Design Tool to get an idea of what is feasible, although modelling the drag of the kevlar line would be a little hard.
The projectile would sleeve over the barrel rather than a traditional "muzzle loaded" approach.
Sort of like a 20 cm leichter Ladungswerfer spigot mortar?

Image

That means you're going to need relatively high pressure in the barrel to make it work.

With regards to the pressures that CO2 capsules can generate, here's a handy chart for a 12 gram:

Image
With some of the QEV designs I've looked at they tend to utilize a mechanical triggering system ( ball valve, air gun trigger, exhaust hand slide valves, etc) I would like to use a solenoid or have a way of having the qev triggered with the means of electrical switch.
If you have a look around eBay there are plenty of solenoid valves available at a reasonable price that could be used to pilot a quick exhaust valve.

The length restriction suggests that an over-under configuration would be the best.

Here's a rough simulation in GGDT that suggests with a single 12 gram cartridge in a 3 inch dia 6 inch long chamber and using a 3/4" QEV with a 6 inch long 1.5" "barrel" you could throw a 900 gram projectile around 80 feet:

Image

This ignores the line drag but suggests that your 45 foot goal is feasible within the parameters described.

A smaller volume chamber keeping the gas at higher pressure will result in better performance, for example with a 1.5 inch diameter chamber of the same length and the pressure at just over 500 psi, the velocity in the model jumps from 51 feet per second to 76 feet per second, which more than doubles the range. The downside is that construction would have to be much stronger to keep the pressure in, with cheap and easy PVC tubing not being an option.
hectmarr wrote:You have to make many weapons, because this field is long and short life
Genadmm
Private
Private
Posts: 3
Joined: Wed Mar 20, 2019 11:35 pm

Mon Mar 25, 2019 10:13 am

Thanks!

I'll be using the GGDT shortly. It looks like a great program.

Yes, sort of like the Leichter Ladungswerfer it would sleeve over the barrel.

From the 12g Co2 chart it seems that the pressure rises significantly below 3" diameter. For my application the largest diameter I can fit would be 2" and only 6 inches long. This would put me at the minimum pressure being 286 psi. I do not plan on using pvc, but primarily metal piping. Preferably I'd like to stick to copper as its easy to put together and its lightweight. The other option would be steel piping but the weight may be a potential issue for my application. Would Type K copper piping be able to withstand almost 300psi? Also I can't seem to find any solenoids or QEV valves that operate at this high level of pressure. What would you suggest for working at this pressure?(connectors, piping, solenoid, QEV valve). (1.5inch diameter chamber would be optimal for my size constraints, and I would most likely have to be using steel piping at that pressure. Is there a relatively small QEV that can operate *somewhat safely* at 500psi?)

I agree the design would be an over-under configuration to save on space.

*random thought*
Also just thinking about function, how do 12gram Co2 paintball pistols function and at what pressure? Clearly they've got the design down pretty good.
User avatar
Anatine Duo
Specialist
Specialist
Canada
Posts: 186
Joined: Sat Feb 01, 2014 11:16 am
Location: cottage country
Has thanked: 36 times
Been thanked: 20 times

Tue Mar 26, 2019 5:31 am

Liquid co2 powered launchers all function at the vapor pressure of c02, about 800 psi. Most bb and pellet co2 guns have tiny hammer valves. Paintball might have a spool valve but mine all had hammer valves.

Copper pipe strength:
https://www.copper.org/applications/plu ... burst.html

It's an interesting project. If you can't find a strong valve you need a large reservoir and barrel to run more volume at low pressure.

The only valves I have access to (can afford) with 500 psi ratings are ball valves. With a short barrel you need to open it fast.

Personally I would build what I can afford and see what it can do... fun, educational...
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Tue Mar 26, 2019 5:59 am

Would Type K copper piping be able to withstand almost 300psi?
https://www.engineeringtoolbox.com/copp ... -d_84.html

OK for pressure, but copper is also a very good conductor of heat and CO2 is temperature sensitive, so I would factor in some insulation too.
Also I can't seem to find any solenoids or QEV valves that operate at this high level of pressure. What would you suggest for working at this pressure?
You probably haven't been looking hard enough, here's one on eBay: https://www.ebay.com/itm/SPARTAN-SCIENT ... xydlFSshD8

Image

For high performance without incurring too much expense, you could get away with a cheap QEV of this type:

Image

While nominally having a lower rating, they can safely take 300 psi or so.

You then use a much smaller solenoid to pilot this QEV: https://www.ebay.com/itm/Parker-73212SN ... ctupt=true

Image
Also just thinking about function, how do 12gram Co2 paintball pistols function and at what pressure? Clearly they've got the design down pretty good.
They're moving smaller projectiles at higher velocities so not really applicable to your case, in order to achieve the performance you're after dumping an entire 12 gram cartridge per shot seems like it will be necessary.

Image

The operation is at the full 800 psi + from the CO2 cartridge, but a hammer valve would be a complex undertaking that takes up more space. I modeled a hammer valve with a 1/2" seat in GGDT and it seems like it should give you at least two or three useful shots but again, you're not going to find off-the-shelf parts and it will take up a larger envelope.

Image

If you have access to a lathe and mill it would be conceivable to design and build this and use a solenoid as a hammer, but this would demand a substantial voltage so you're adding the size and weight of batteries and capacitors and the electronics to control them to your setup.
hectmarr wrote:You have to make many weapons, because this field is long and short life
User avatar
farcticox1
Sergeant
Sergeant
Posts: 1077
Joined: Sun Mar 31, 2013 12:37 pm
Has thanked: 68 times
Been thanked: 93 times

Tue Mar 26, 2019 4:31 pm

I just got that 04 QEV for my launcher :D exhaust port is 3/8" NPT although they call it a 1/2" QEV :o
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Wed Mar 27, 2019 5:01 am

farcticox1 wrote:exhaust port is 3/8" NPT although they call it a 1/2" QEV :o
eBay dimensions should be taken with a pinch of salt, for example the thread diameter might be approximately 1/2" and it will be called a 1/2" valve, when in fact it's a 1/4" NPT valve.
hectmarr wrote:You have to make many weapons, because this field is long and short life
Genadmm
Private
Private
Posts: 3
Joined: Wed Mar 20, 2019 11:35 pm

Wed Mar 27, 2019 12:08 pm

Thanks for the links.

Is it possible to make my reservoir in a U shape instead of having a straight singular tube? I could then do an Over-under design with the reservoir and decrease my pressure because the volume is increased, correct? To get roughly 300psi I would need to use 10" of 1.5" diameter pipe, so if I were to use two sections of 5" 1.5" diameter pipe I would achieve the same volume within my 8 inch size constraint.

Also I currently have an 18v dc power supply on the apparatus that can power a solenoid valve. I also have access to a lathe and a mill.

at 300psi would brass connectors be appropriate?
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Fri Mar 29, 2019 3:41 am

Genadmm wrote:Is it possible to make my reservoir in a U shape instead of having a straight singular tube? I could then do an Over-under design with the reservoir and decrease my pressure because the volume is increased, correct? To get roughly 300psi I would need to use 10" of 1.5" diameter pipe, so if I were to use two sections of 5" 1.5" diameter pipe I would achieve the same volume within my 8 inch size constraint.
Technically you'd be generating more turbulence but in practice it's not going to affect the performance that much.
Also I currently have an 18v dc power supply on the apparatus that can power a solenoid valve. I also have access to a lathe and a mill.


Here is an example of a solenoid actuated hammer valve from spudfiles:

[youtube][/youtube]

Thread here.

You would definitely need a balanced valve, I used one in my latest build.
at 300psi would brass connectors be appropriate?
If they are suitably rated, yes. Currently have brass fittings on our 4500 psi nitrogen tanks.

The question to ask yourself is whether you will go for a relatively easy build using mostly off-the-shelf parts that will dump a 12g CO2 capsule for every shot, or go for a more complex build with custom parts and a bit of R&D that will be more efficient.
hectmarr wrote:You have to make many weapons, because this field is long and short life
User avatar
farcticox1
Sergeant
Sergeant
Posts: 1077
Joined: Sun Mar 31, 2013 12:37 pm
Has thanked: 68 times
Been thanked: 93 times

Fri Mar 29, 2019 4:01 am

Over under like this works fine
006 (1).jpg
Or chamber to the rear (front is just PVC)
SS (1).jpg
I mostly use these brass fittings, they are rated at 800psi. Anything you get should have a working pressure rating.
brass.png
Post Reply