Double barrelled 3x hybrid

Harness the power of precision mixtures of pressurized flammable vapor. Safety first! These are advanced potato guns - not for the beginner.
User avatar
spudamine
Specialist
Specialist
Posts: 184
Joined: Sun Nov 23, 2008 2:47 pm

Thu Jul 19, 2012 2:08 pm

This is yet another of my completely un-planned cannons, seeing a pack of these on the shelf:
Image

I was intrigued and couldn't resist the dual temptations of alcoholic beverage and a novel preesure vessel. The lager was unexceptional but I liked the aluminium bottles, the necks were about the right size for a 1/2" tap so I thought what the hell and a few weeks later this was sitting on my work bench:

Image
Image

Details
I'm not really into pneumatics these days so my first though was a straight up combustion, however the power would have been puny through the 1/2" orifice, so I thought I'd add a few x :)
Of course this brought up the obvious problem of the beer bottles exploding so they were sleeved with aluminium tube which was cross-bolted at the end and filled with wire mesh and hot glue. This gave me a chamber sufficiently safe up to about 3x, enough for some fun.To finish off I thought I'd give it two independently firing barrels and chambers. Finally hybrids are noisy beasts so barrel shrounds / suppressors were mandatory.

Image
Ignition is by two BBQ piezo units, one actually came out of my old barbecue which had rusted to bits (the rest gets shot in the video). The electrodes were tricky due to the wall of the chamber not really being thick enough to take a thread, i used an M8 mylon bolt with channels dremmeled down the side for enamelled winding wire electrodes, all tapped and epoxied in.
As i was determined not to buy anything for this project i didn't bother with proper unions for the burst disks, just used some pipe fittings epoxied together. This worked well although the rotating barrels gave poor accuracy (who cares, it's a shotgun)
Image
For metering I tried JSR's syringe technique which worked flawlessly, ignition first time. I've fired this thing a lot and it's not failed to ignite the mixture a single time. It just goes to show you don't need a hundred pressure guages attached to a hybrid to get it too work, one on the pump is sufficient (for low mixes/small chambers anyway).
Image
This is probably my favourite damage pic, this was only 1mm steel but the projectile punched a perfect full bore disk out of the target.

And finally the damage vid :D

[youtube][/youtube]
Last edited by jrrdw on Sun Nov 17, 2013 9:41 am, edited 1 time in total.
Reason: Fixed video.
User avatar
al-xg
Corporal 2
Corporal 2
Great Britain
Posts: 643
Joined: Fri Jan 19, 2007 12:29 pm

Thu Jul 19, 2012 2:49 pm

Wow, quite an impressive canon and video there !
Looks like that will be quite popular.
User avatar
AircannonSweden
Specialist
Specialist
Posts: 131
Joined: Thu Oct 27, 2011 11:53 am
Location: Sweden,Linköping

Thu Jul 19, 2012 3:05 pm

Looks very good :)
As always,have a nice day - FPSrussia
User avatar
killerbanjo
Specialist 2
Specialist 2
Posts: 245
Joined: Fri Jun 18, 2010 6:56 pm

Thu Jul 19, 2012 3:23 pm

Oh damn that is VERY sexy!!! Nice work mate :D
User avatar
POLAND_SPUD
Captain
Captain
Posts: 5402
Joined: Sat Oct 13, 2007 4:43 pm
Been thanked: 1 time

Thu Jul 19, 2012 9:37 pm

yet another so I got drunk and thought... :D
Children are the future

unless we stop them now
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Fri Jul 20, 2012 1:29 am

:shock:

Wow, just wow. This is everything I believe in! Hybrid, syringe fuelling, epoxy thrown in, full bore finned darts.... Brilliant!

Your "shotgun" sabots seem to be letting you down though, looks like they're coming apart in the barrel and not transferring all the energy to the projectile.

What do the suppressors look like internally?

Glad to see you using a syringe, I believe that manometric metering is something that puts a lot of pneubs off when building a hybrid, this is much easier and cheaper to set up.

Excellent work as always!
hectmarr wrote:You have to make many weapons, because this field is long and short life
User avatar
MrCrowley
Moderator
Moderator
Posts: 10078
Joined: Fri Jun 23, 2006 10:42 pm
Location: Auckland, New Zealand
Been thanked: 3 times

Fri Jul 20, 2012 1:32 am

jackssmirkingrevenge wrote:I believe that manometric metering is something that puts a lot of pneubs off when building a hybrid, this is much easier and cheaper to set up.
Na, it's definitely volumetric (excluding syringe metering)! :D

No one really uses manometric metering anyway :(
But there's one fixed pressure for each gas at each mix regardless of chamber size. No need to measure your chamber volume with water. All you need is one accurate 0-15PSI gauge and one normal 0-150PSI gauge.

That being said, I love the ingenuity of this cannon. Naturally, I wouldn't have said that if it weren't a hybrid. Good job :P
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Fri Jul 20, 2012 1:36 am

MrCrowley wrote:All you need is one accurate 0-15PSI gauge and one normal 0-150PSI gauge.
Think of how many big syringes you could buy for the price of those ;)
hectmarr wrote:You have to make many weapons, because this field is long and short life
User avatar
DYI
First Sergeant 5
First Sergeant 5
Antigua & Barbuda
Posts: 2862
Joined: Sat Jul 07, 2007 8:18 pm
Location: Here and there

Fri Jul 20, 2012 7:42 am

All you need is one accurate 0-15PSI gauge and one normal 0-150PSI gauge.
Or one really accurate 0-5000psi gauge... :lol:

That's an interesting use of beer bottles. It's nice to see people just "throwing together" hybrids - with proper construction, they really are very simple. Four years ago, this would've been yet another 1X combustion gun.
Spudfiles' resident expert on all things that sail through the air at improbable speeds, trailing an incandescent wake of ionized air, dissociated polymers and metal oxides.
User avatar
mark.f
Sergeant Major 4
Sergeant Major 4
Eritrea
Posts: 3627
Joined: Sat May 06, 2006 11:18 am
Location: The Big Steezy
Has thanked: 52 times
Been thanked: 53 times
Contact:

Donating Members

Fri Jul 20, 2012 7:54 am

Girls, girls, you're both very pretty. :P

Excellent job Spudamine. The bottle chambers seemed to be a little more trouble than they're worth but the double barrelled design is awesome. Not something I've seen in a hybrid yet.
User avatar
spudamine
Specialist
Specialist
Posts: 184
Joined: Sun Nov 23, 2008 2:47 pm

Fri Jul 20, 2012 2:13 pm

Thanks for all the comments guys.
What do the suppressors look like internally?
They're a bit primitive really, just some holes drilled in the barrel near the muzzle and the outer chamber filled with wire wool and sealed, I'm not convinced they're doing a lot but I didn't want to have to build two complex suppressors.
The bottle chambers seemed to be a little more trouble than they're worth

They're the reason this cannon exists but I did find myself thinking I could have swapped them out for paintball tanks for a rather sweet 10x :)
Still it worked out rather nicely, even with all the reinforcement they have a nice strength to weight ratio.
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Fri Jul 20, 2012 11:43 pm

spudamine wrote:They're a bit primitive really, just some holes drilled in the barrel near the muzzle and the outer chamber filled with wire wool and sealed, I'm not convinced they're doing a lot but I didn't want to have to build two complex suppressors.
Sometimes it's hard to judge the performance of a suppressor, but even a crude one will take the edge of the muzzle "crack".
They're the reason this cannon exists but I did find myself thinking I could have swapped them out for paintball tanks for a rather sweet 10x :)
A certain crazy French forum member took paintball bottles to 40x :D
Still it worked out rather nicely, even with all the reinforcement they have a nice strength to weight ratio.
I would probably be comfortable taking them to 5x at least, but then again I'm not known for launchers that don't spread their parts around in a violent manner :D
hectmarr wrote:You have to make many weapons, because this field is long and short life
User avatar
spudamine
Specialist
Specialist
Posts: 184
Joined: Sun Nov 23, 2008 2:47 pm

Sat Jul 21, 2012 1:26 am

A certain crazy French forum member took paintball bottles to 40x
Alas said crazy frenchman also has a nice field to shoot in, not a garage attached to the side of his house :(

I was going to take it up to 4x but I first found a 60ml syringe, then calculated the required fuel volume as something like 60.2ml, which I consider fate :)

Something strange i've noticed about this cannon, the right barrel appears to be consistenly more powerful than the left. for example look at the .177 pellet shot into the plywood, on the left barrel only one pellet makes it through, the right just blows a big hole through. I've also had two misfires on the left (ignition but failiure to burst the disk) and none on the right.
This is particularly odd as the two chambers, barrels and burstdisk holders are identical. The only potential difference is the ignition :?:
User avatar
hawktalk
Private 4
Private 4
Wales
Posts: 73
Joined: Sat Apr 07, 2012 11:23 am

Mon Sep 03, 2012 5:38 am

stunning creation, its very shiny 8)
PotatoEnemy17
Specialist
Specialist
Posts: 100
Joined: Tue Apr 10, 2012 6:33 pm

Tue Sep 04, 2012 10:19 am

Awesome Cannon, Kinda reminds me of when I built a cannon with water bottles - oh wait that one turned in to a bomb, oops! It looks pretty ergoomic :P
Post Reply