imagine this: cylinder filled with water with water with an inflatable rubber bladder in the center, pressure gauge on side of cylinder. I inflate the bladder to 60 psi (bladder is pushing against the water now). will the gauge read 60 psi?
also what psi are standard "long and skinny" blow torch propane tanks set at?
-thanks
seems logical but I just want to double check...
-
- Corporal 5
- Posts: 913
- Joined: Wed Oct 19, 2005 7:54 pm
Movie dialogue: "The good die first."
Tom: "But most of us are morally ambiguous, which explains our random dying
patterns."
Tom: "But most of us are morally ambiguous, which explains our random dying
patterns."
-
- Staff Sergeant 2
- Posts: 1603
- Joined: Sat Aug 11, 2007 6:59 pm
- Been thanked: 1 time
I imagine the gauge would read 60psi (although if placed at the bottom of the cylinder you would have to take into account the weight of the water)
Propane liquifies at 90psi so i would think it would be "set" at around that, maybe a little more. Hope this helps
Propane liquifies at 90psi so i would think it would be "set" at around that, maybe a little more. Hope this helps
-
- Corporal 5
- Posts: 913
- Joined: Wed Oct 19, 2005 7:54 pm
thanks
Movie dialogue: "The good die first."
Tom: "But most of us are morally ambiguous, which explains our random dying
patterns."
Tom: "But most of us are morally ambiguous, which explains our random dying
patterns."
-
- Sergeant Major
- Posts: 3198
- Joined: Wed Mar 28, 2007 9:48 am
- Location: Greenwood, Indiana
- Has thanked: 5 times
- Been thanked: 15 times
- Contact:
pyromanic13, what you describe is a basic water well storage tank. The pressure of the water is the same as the pressure in the bladder.
Propane tanks contain a mixture of gaseous and liquid propane. As long as both phases are present the pressure in the bottle is only dependent on the temperature. (The boling point of propane is -44F)
For propane at 80F the pressure is 128 PSIG.
Propane tanks contain a mixture of gaseous and liquid propane. As long as both phases are present the pressure in the bottle is only dependent on the temperature. (The boling point of propane is -44F)
For propane at 80F the pressure is 128 PSIG.
Code: Select all
Propane Vapor Pressure Chart, PSI
Temp. Pressure
(F) (PSI)
–30° 6.8
–20° 11.5
–10° 17.5
0° 24.5
10° 34
20° 42
30° 53
40° 65
50° 78
60° 93
70° 110
80° 128
90° 150
100° 177
110° 204
-
- Corporal 5
- Posts: 913
- Joined: Wed Oct 19, 2005 7:54 pm
do you guys think I should regulate? max psi for 2" sch 40 is 280 psi... plus should the pressure get too high I can turn off the propane via torch valve then dump the pressure via tee valve.
I'd rather not spend the money...regs on mcmaster are 80$
I'd rather not spend the money...regs on mcmaster are 80$
Movie dialogue: "The good die first."
Tom: "But most of us are morally ambiguous, which explains our random dying
patterns."
Tom: "But most of us are morally ambiguous, which explains our random dying
patterns."
-
- Sergeant Major
- Posts: 3198
- Joined: Wed Mar 28, 2007 9:48 am
- Location: Greenwood, Indiana
- Has thanked: 5 times
- Been thanked: 15 times
- Contact:
Pyro: I don't think a regulator is required. It might help, and be a bit safer, if the orifice between the propane tank and the chamber was pretty small. That will make the pressure in the chamber rise slowly. The standard, very tiny, orifice on a benomatic torch puts out something like 10cc/second (~0.6ci/sec) into a syringe. That might be a bit slow for a chamber of a hundred or so cubic inches but it would be a good starting point. If it is too slow you could drill the orifice out a bit.
-
- Corporal 5
- Posts: 913
- Joined: Wed Oct 19, 2005 7:54 pm
sorry but could you clarify... are you talking about how much propane exits the tank in one sec or how much propane exits the otrch nozzle
the torch head is cut in two...the tiny hole/flame part is at near the blowguns exit. the valve and size of the torch pipe hole is connected to the propane tank.
the torch head is cut in two...the tiny hole/flame part is at near the blowguns exit. the valve and size of the torch pipe hole is connected to the propane tank.
Movie dialogue: "The good die first."
Tom: "But most of us are morally ambiguous, which explains our random dying
patterns."
Tom: "But most of us are morally ambiguous, which explains our random dying
patterns."