Hybrid design

Harnessing precision mixtures of pressurized flammable vapor. Not for the beginner.
Gunner
Specialist
Specialist
Posts: 111
Joined: Sun Oct 21, 2007 9:05 am

I`m planning to do my first hybrid cannon and I have a few question from it:

I will make 500ml chamber and is this good size: 5cm x 25cm?

And the second question , I am not sure but, must there be is chamber fan?

Thanks!
Back in business!
User avatar
CasinoVanart
Specialist 2
Specialist 2
Posts: 281
Joined: Wed Jul 30, 2008 1:10 am

You may want to do a bit of research first Gunner, start with the Hybrid showcase.
May i ask what types of cannons you have built before?

And no, no fan.
Gunner
Specialist
Specialist
Posts: 111
Joined: Sun Oct 21, 2007 9:05 am

Combustion cannons and pneumatics...and I have done some research but I have not found yet what I am looking for.
Back in business!
Gunner
Specialist
Specialist
Posts: 111
Joined: Sun Oct 21, 2007 9:05 am

Hmm, I made my chamber, it is 3cm ID and 20cm long and it is about 150ml and I am planning to use 6x mixes, Is the DDT how possible?
Back in business!
User avatar
Hubb
First Sergeant 2
First Sergeant 2
Posts: 2390
Joined: Mon May 28, 2007 8:39 am
Location: South Georgia
Contact:

DDT is very possible with that. I've never experienced DDT (not intentionally) but the research I've done suggests that a long, thin chamber is more prone to DDT than a short, fat one. What OD is the chamber?
brogdenlaxmiddie
Corporal
Corporal
Posts: 562
Joined: Sun Jul 22, 2007 2:19 pm

In this case, I wouldn't be worried about DDT. I would be more worried if your chamber could even take the pressures of a hybrid. You mentioned the diameter and length, but not material. I also don't neccisarrily believe that you should be making a hybrid quite yet. If you were, you wouldn't of asked these questions. However, it is nice that you did ask because that shows you at least care. :wink:
Gunner
Specialist
Specialist
Posts: 111
Joined: Sun Oct 21, 2007 9:05 am

Here is the chamber and the ignition box: http://www.aijaa.com/v.php?i=2470935.jpg

The chamber ID is 30mm and OD 32mm and I think that you can quess what material it is :D
Back in business!
User avatar
SpudFarm
First Sergeant 3
First Sergeant 3
Posts: 2571
Joined: Sat Nov 04, 2006 9:39 am
Location: Norway Trondheim area

do not put 6x in that thing, the soldering looks bad..
"Made in France"
- A spud gun insurance.
User avatar
bob-a-lu
Specialist
Specialist
Posts: 138
Joined: Fri Jul 06, 2007 12:24 pm
Location: alabama

i agree with spud farm and u dont need a fan because the fuels pressurated
User avatar
SpudFarm
First Sergeant 3
First Sergeant 3
Posts: 2571
Joined: Sat Nov 04, 2006 9:39 am
Location: Norway Trondheim area

not because the fuel is under pressure more because it will be mixed with the incomming air and the shot wont go until the disk burst's what so ever
"Made in France"
- A spud gun insurance.
Gunner
Specialist
Specialist
Posts: 111
Joined: Sun Oct 21, 2007 9:05 am

Well , I will start with 2x mixes and then 3x and... but I put with my 12V compressor 18bar in that and after one hour the pressure was still same :).
Back in business!
User avatar
SpudFarm
First Sergeant 3
First Sergeant 3
Posts: 2571
Joined: Sat Nov 04, 2006 9:39 am
Location: Norway Trondheim area

6x would be more like 40bar
"Made in France"
- A spud gun insurance.
Gunner
Specialist
Specialist
Posts: 111
Joined: Sun Oct 21, 2007 9:05 am

Yeah I know but now some edit:

I made three shots without barrel: 1x,2x,3x and then it fired every time and the sound... it was like shotgun :D . I will soon buy the barrel and then the fun begins :twisted: .

Here is pic: http://www.aijaa.com/v.php?i=2476912.jpg
Back in business!
User avatar
SpudFarm
First Sergeant 3
First Sergeant 3
Posts: 2571
Joined: Sat Nov 04, 2006 9:39 am
Location: Norway Trondheim area

i would not go over 4x..

but congratts, you made a hybrid :)
"Made in France"
- A spud gun insurance.
Gunner
Specialist
Specialist
Posts: 111
Joined: Sun Oct 21, 2007 9:05 am

How possible the DDT would be in 6x? :D
(I am not trying...yet)
Back in business!
Post Reply

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Register

Sign in

  • Similar Topics
    Replies
    Views
    Last post
  • 6mm hybrid design
    by jackssmirkingrevenge » » in Hybrid Cannons
    31 Replies
    10800 Views
    Last post by jackssmirkingrevenge
  • New hybrid design
    by daxspudder » » in Hybrid Cannons
    1 Replies
    3014 Views
    Last post by mark.f
  • Hybrid QDV Design
    by saefroch » » in Hybrid Cannons
    12 Replies
    2649 Views
    Last post by saefroch
  • New hybrid design
    by pat123 » » in Hybrid Cannons
    16 Replies
    5471 Views
    Last post by Jared Haehnel
  • New Hybrid design
    by boyce123 » » in Hybrid Cannons
    22 Replies
    7866 Views
    Last post by jackssmirkingrevenge