Non Pressure Rated PVC Cement?

Post Reply

16 posts

Safe or Unsafe?

Safe: 3; 60%

Unsafe: 2; 40%

: Total votes: 5

SubsonicSpud: Specialist 2; Posts: 205; Joined: Sat Jan 03, 2009 8:55 am; Location: Australia; Has thanked: 2 times; Been thanked: 1 time

Quote

Wed May 13, 2009 2:23 am

TurboSuper wrote:Errr...you don't have to sand the joints. The solvent actually melts them together so increasing the surface area is kinda moot. Cleaning them is necessary, though.

I know sanding is not required, but because he did not use primer sanding would have helped the cement bond by providing a freshly exposed surface.

Subsonicspud

Post Reply

16 posts

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Sign in

Similar Topics

Replies

Views

Last post

Cement molds and making cement slugs

Last post by windshrike « Fri Oct 19, 2007 3:44 pm
Posted in Ammo & Materials
Replies: 18
by gwoloshyn » Thu Oct 18, 2007 8:28 pm » in Ammo & Materials
1

2
First post

For my new air cannon, which I will post this weekend when I finish it, is going to shoot these cement slugs I made. Pretty straight forward, cut pvc...

Last post

Make it a bit small and wrap it in duct tape to prevent wear in the barrel.
18 Replies

8248 Views

Last post by windshrike
Fri Oct 19, 2007 3:44 pm
Pressure rated DWV?

Last post by frankrede « Sun Jul 01, 2007 4:43 am
Posted in Ammo & Materials
Replies: 55
by spudthug » Wed Jun 27, 2007 3:39 pm » in Ammo & Materials
1

2

3

4
First post

ok well i went to the hardware store today looking for some cheap parts because usually they are the best priced.. i asked if he had 4 inch pressure...

Last post

check for a local irrigation supply store for larg diameter pipes and fittings at lower prices and a larger selection. I suggest looking for a Ewings
55 Replies

16642 Views

Last post by frankrede
Sun Jul 01, 2007 4:43 am
Pressure rated dwv?

Last post by jimmy101 « Sun Jun 22, 2008 2:31 pm
Posted in Ammo & Materials
Replies: 30
by igpay » Tue Jun 17, 2008 11:42 am » in Ammo & Materials
1

2

3
First post

Ok, so yesterday I went down to the local osh and bought two lengths of pipe. two feet of 2 and two feet of 1 . The two inch pipe says, J-M...

Last post

personally i don't know how you can mix up the two numbers, ie 4000 and 200 or in my case 70-80.
You have to remember the audience of this forum....
30 Replies

10199 Views

Last post by jimmy101
Sun Jun 22, 2008 2:31 pm
Pressure Rated DWV?

Last post by mattyzip77 « Thu Jun 27, 2013 8:33 pm
Posted in Ammo & Materials
Replies: 4
by Backyard Pneumatic » Sun Jun 23, 2013 11:24 am » in Ammo & Materials

First post

Hey Guys, new member here with a materials question. I'm finally getting started on my first serious pneumatic, a 3 piston valve launcher, and was...

Last post

the bushing should be fine... Just check for cracks>>>>

4 Replies

5250 Views

Last post by mattyzip77
Thu Jun 27, 2013 8:33 pm
how well does non-pressure rated sch 40 pvc do?

Last post by MrCrowley « Fri Feb 09, 2007 6:27 am
Posted in General Cannon Discussion
Replies: 5
by imjustpk » Fri Feb 09, 2007 1:46 am » in General Cannon Discussion

First post

im wondering if non pressure rated coextruded pvc is alright in pressure capabilities. i imagine it to be better than abs, but does anyone know about...

Last post

Was it the underlining? I just underlined them to make sure people read correctly and carefully. :P

5 Replies

1402 Views

Last post by MrCrowley
Fri Feb 09, 2007 6:27 am

Return to “Combustion Cannons”

Non Pressure Rated PVC Cement?

Safe or Unsafe?

Create an account or sign in to join the discussion

Create an account

Sign in

Login • Register