HYBRID FUELING 101

Harness the power of precision mixtures of pressurized flammable vapor. Safety first! These are advanced potato guns - not for the beginner.
User avatar
saefroch
Staff Sergeant 2
Staff Sergeant 2
Posts: 1679
Joined: Mon Jun 08, 2009 8:47 am
Location: U.S.A.- See Map

Tue Jan 25, 2011 9:36 pm

Okay, so just simplifying the calculations on the first page for calculating for chamber fueling, I get the equation mix/(1-fuel%)-mix = Fuel pressure
Then fill with 1-mix# atm of oxidizer

Correct?
User avatar
POLAND_SPUD
Captain
Captain
Posts: 5402
Joined: Sat Oct 13, 2007 4:43 pm
Been thanked: 1 time

Sat Feb 05, 2011 9:07 pm

if I use butane I'd need 4.54639248psi for a 10X mix, right ? (assuming that the ideal mix is 3%, though I am not sure if that's correct)
Children are the future

unless we stop them now
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Sat Feb 05, 2011 9:55 pm

POLAND_SPUD wrote:(assuming that the ideal mix is 3%, though I am not sure if that's correct)
It is.
doyourselfit wrote:@POLAND: Although manometric meters are nice, they're not the most practical with lower mixes, especially if you're using a small chamber.
Sound advice.

I'm chucking this here too:

[youtube][/youtube]

For a hybrid mix, just multiply the resulting fuel volume by whatever mix number you want to achieve.

It's important that you consider the dead space after the check valve of your pump to be part of the chamber volume when making your calculations, especially for small chambers.

The calculation is as follows:

(ideal fuel % / 100) x (chamber + pump dead volume) x mix number


In the case of this Beto shock pump, the dead volume is 1.75mL. For a 10mL chamber using butane to say 5x, the calculation is as follows:

3/100 x (10+1.75) x 5 = 1.76mL of butane

Had we not considered the pump dead volume, the result would have been 1.5mL of fuel, an error of 15% which would most likely prevent ignition. If it were a 100mL chamber on the other hand, the error would have been of 1.5%, and likely the mix would have still ignited.

After the fuel is injected, all you have to do is pressurise with your pump to the following pressure (assuming you're using psi):

(mix number - 1) x 14.7

In the case of our 5x mix, the calculation is as follows:

(5-1) x 14.7 = 59 psi

If your gauge can read bar, simply pressurise to (mix number - 1) bar, so 4 bar in this case.
Last edited by jackssmirkingrevenge on Tue Feb 27, 2018 7:36 pm, edited 1 time in total.
hectmarr wrote:You have to make many weapons, because this field is long and short life
User avatar
POLAND_SPUD
Captain
Captain
Posts: 5402
Joined: Sat Oct 13, 2007 4:43 pm
Been thanked: 1 time

Sat Feb 05, 2011 10:08 pm

I'm chucking this here too:
Yeah, I got that 3% from your vid
:D
Sound advice
yeah it might be. But is 10x mix a low mix ?

AFAIK 4.54639248psi = 235mmhg, which is in range of my gauge... So guess I might as well give it a try
If your gauge can read bar, simply pressurise to (mix number - 1) bar, so 4 bar in this case
W8 a second... so I am supposed to pressurise the chamber to 9bar for a 10X mix ? (note that I still want to use manometric metering)

Lol if jsr is posting fuelling calculations then it means that the apocalypse is near :D
Children are the future

unless we stop them now
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Sat Feb 05, 2011 10:51 pm

POLAND_SPUD wrote:Yeah, I got that 3% from your vid
Hence your "though I am not sure if that's correct" WImage

:D :D :D

You're more likely to believe Jimmy, it's actually 3.23%, but I wanted to keep things simple for your average youtube viewer :D
jimmy101 wrote:Complete combustion of butane (C4H10) in air (~21% O2, 29% nitrogen) produces carbon dioxide (CO2) and water as described by the equation:

2 C4H10 + 13 O2 = 8 CO2 + 10 H2O + heat

The equation tells us that for each 13 molecules of oxygen we need 2 molecules of butane. Since air is only ~21% oxygen we need (21%)(2/13) = 3.23% by volume butane in the combustion chamber.


Luckily, we have a bit of leeway:
jimmy101 also wrote:Butane in air will only burn if the percentage of butane is in the range of 1.9% to 8.4%. Outside that range the mixture can not be ignited.


... so 3% is just fine ;)
So guess I might as well give it a try
Perhaps, if you already have the equipment
W8 a second... so I am supposed to pressurise the chamber to 9bar for a 10X mix ? (note that I still want to use manometric metering)
For a 10x mix, you want 10 bar in the chamber. You already have 1 bar in there (assuming you're not working in a vacuum) and when your gauge reads zero, it's zero relative to atmospheric pressure, it should be reading 1 bar.
Lol if jsr is posting fuelling calculations then it means that the apocalypse is near :D
Yep, 2012 is fast approaching and my army of space monkeys isn't nearly as big as it needs to be!
hectmarr wrote:You have to make many weapons, because this field is long and short life
User avatar
POLAND_SPUD
Captain
Captain
Posts: 5402
Joined: Sat Oct 13, 2007 4:43 pm
Been thanked: 1 time

Sat Feb 19, 2011 9:33 pm

I've just realized something... to fuel a hybrid one has to fill a closed chamber (already filled with air at atmospheric pressure) with propane/butane/mapp. When the pressure in the chamber reaches a set value regulated air has to be added

What if I just purge the chamber with propane to make sure that it contains only propane (not air) and then add air at X bar ? Wouldn't that be a better and simpler idea?

so if the ideal ratio for butane is 3% then fill the chamber completely, close the vent and fill with air to 33bar

EDIT
lol either it is a pretty clever idea or I am just to tired to think.
Anyway this is what I think would work fine:
1.butane is feed into the chamebr via a check valve
2. on the other end of the chamber is a 3 way valve
3. In normal position the 3 way acts as a vent, when actuated it blocks off vent port and fills the chamber with regulated air
4. When the valve is actuated the check valve blocks the flow (since the pressure in the chamber increases)
Children are the future

unless we stop them now
User avatar
Crna Legija
First Sergeant 2
First Sergeant 2
Posts: 2333
Joined: Sun Jul 20, 2008 5:14 am
Location: australia

Sat Feb 19, 2011 10:12 pm

how many 3way valves do you own?
'' To alcohol... The cause of, and solution to, all of life's problems.”
--Homer Simpson

Add me on ps3: wannafuk, 8/11/11 cant wait
User avatar
POLAND_SPUD
Captain
Captain
Posts: 5402
Joined: Sat Oct 13, 2007 4:43 pm
Been thanked: 1 time

Sat Feb 19, 2011 10:45 pm

lol a lot... but it isn't important - this thing would need just one

maybe I should have explained it better. The idea is simple instead of metering regulated fuel and then air I purge the chamebr with butane. If the ideal mix for butane is ~3% and I've got 100% of it in the chamber so I need to add 33 times the volume of the chamber of air.

To do so I just fill it up with air to 33 bar

So is it a good idea or am I retarded?
Children are the future

unless we stop them now
User avatar
DYI
First Sergeant 5
First Sergeant 5
Antigua & Barbuda
Posts: 2862
Joined: Sat Jul 07, 2007 8:18 pm
Location: Here and there

Sun Feb 20, 2011 10:54 am

Well, your idea works so long as you don't mind being stuck to a certain mix number.

Achieving a full purge of the chamber could be an issue in terms of fuel wasted if you're doing it using the method you described above. Although it may not be quite so convenient, depending on implementation, filling the chamber with a liquid and then displacing it with fuel would be less wasteful, and more likely to result in the chamber being completely purged.

The purging method would also make it easier to attain the maximum ~220X achievable with gaseous propane at roughly room temperature (although it wouldn't alter the maximum, only bring the required fueling pressure down to the same value as the tank pressure).

Also, I'd like to add that in the case where pure O<sub>2</sub> is being used as the oxidiser, this method isn't the greatest idea - detonations are even more likely when that comparatively small amount of nitrogen is removed completely from the mix, as Larda's experience testing HyGaC20 indicates.
Spudfiles' resident expert on all things that sail through the air at improbable speeds, trailing an incandescent wake of ionized air, dissociated polymers and metal oxides.
User avatar
Lockednloaded
Staff Sergeant
Staff Sergeant
United States of America
Posts: 1566
Joined: Thu Sep 03, 2009 9:38 pm
Location: Texas, USA
Been thanked: 6 times

Sat Mar 26, 2011 7:20 pm

I'm having some fueling trouble thats just making me feel like an idiot....

I have a 3/4"x12" chamber with taser ignition and 1/2" cam-lock union, but for some reason I'm having lots of trouble getting my mix to ignite. I put in 13Kpa of propane and 2bars of air for a 3x mix, but nothing's happening. Any tips?
User avatar
saefroch
Staff Sergeant 2
Staff Sergeant 2
Posts: 1679
Joined: Mon Jun 08, 2009 8:47 am
Location: U.S.A.- See Map

Sat Mar 26, 2011 8:23 pm

Just use this. If you can figure out the error with column G while you're at it, kudos and thanks.

And a note to the user: Put in the units that you wish it to return.
Attachments
Hybrid Excel- compatible.zip
(8.61 KiB) Downloaded 586 times
User avatar
Labtecpower
Sergeant 3
Sergeant 3
Eritrea
Posts: 1297
Joined: Sat Feb 20, 2010 6:38 am
Location: Pyongyang
Has thanked: 5 times
Been thanked: 13 times

Mon Apr 11, 2011 3:58 am

Taking the pump's dead space in the calculationsis only needed when using a fill valve wich has an open connection with the pump , right?

I'm planning on using a dunlop valve when filling it, because it doesn't leak when disconnected, like a schrader valve.
User avatar
jackssmirkingrevenge
Five Star General
Five Star General
Posts: 26179
Joined: Thu Mar 15, 2007 11:28 pm
Has thanked: 543 times
Been thanked: 319 times

Donating Members

Mon Apr 11, 2011 4:22 am

If the fill valve is pressure activated then technically it is acting as a check valve and in this case the pump dead volume need not be taken into account.

Note that my shock pump has a separate knob on the attachment head that allows you to independently depress the schrader valve stem, and therefore the chamber does not leak when the head is disconnected.
hectmarr wrote:You have to make many weapons, because this field is long and short life
shardbearer
Private 4
Private 4
Posts: 85
Joined: Sat Apr 23, 2011 10:21 pm

Thu Jun 28, 2012 11:58 am

I simplified the equation for Manometric fueling a bit, hope it helps some people.

(X/R-X)*P

Where X is your mix number, R is fuel ratio (for propane it's .958, butane .9677), and P is ambient pressure (usually 14.7 psi or 1 bar). For example, for propane at sea level with PSI:

(X/.958-X)*14.7

For a 10X mix:

(10/.958-10)*14.7=6.44 psi, the same as SB15 got for a 10X mix.

For measuring in bar, it gets even easier, since atmospheric pressure is 1 bar (well 1.01325, but close enough)

X/.958-X

10/.958-10 = 0.438413361 bar

The math gets much easier when you take out chamber volume, and now you don't have to measure it either :D

Edit:

I think you can simplify the equation much further. Take the equation from above for propane, and calculate for a 1X Mix

(1/.958-1)*14.7 = .64447 psi

And then you can multiply that by the mix number to get the amount of psi.
Easy, huh?

Edit: Just read one of Crowley's posts where he said the exact same thing. :roll: Oh well.
User avatar
Juggernaut12121
Specialist
Specialist
Posts: 140
Joined: Wed Apr 03, 2013 12:47 pm

Tue Sep 06, 2016 4:28 pm

So I'm sorry that this is a really dumb question, but I was looking at the load mix calculator on HGDT and it said that the chamber pressure after the fuel injection (using propane at a 10x mix) was only 5.89PSI whereas it's been stated throughout the thread that 6.44PSI's the proper pressure, am I missing something?
Also, I know it was mentioned somewhere here but I don't believe it was answered, you'd add 132PSI of air in on top of the fuel pressure right? (so for a 10x mix with 6.44PSI of propane the chamber pressure after air injection would be 138.44PSI?).
Whatever the mind can conceive and believe, it can achieve
Post Reply