Will this inflate my airgun?
-
- Specialist 4
- Posts: 458
- Joined: Tue Aug 02, 2011 12:31 pm
- Contact:
just wondering if this would go up to 300 psi? http://www.ebay.co.uk/itm/RAC-HP300-300 ... 500wt_1156
- Gun Freak
- Lieutenant 5
- Posts: 4971
- Joined: Mon Jan 25, 2010 4:38 pm
- Location: Florida
- Been thanked: 7 times
Probably one time
OG Anti-Hybrid
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
-
- Specialist 4
- Posts: 458
- Joined: Tue Aug 02, 2011 12:31 pm
- Contact:
Eh?Gun Freak wrote:Probably one time
- Gun Freak
- Lieutenant 5
- Posts: 4971
- Joined: Mon Jan 25, 2010 4:38 pm
- Location: Florida
- Been thanked: 7 times
They are slow, cheapo depot, weak, and low quality. You are wasting your money to buy one.
OG Anti-Hybrid
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
-
- Specialist 4
- Posts: 458
- Joined: Tue Aug 02, 2011 12:31 pm
- Contact:
I dont have the money to buy a big compressor and its only for my .223 airgun which has a small tank about 25 cm long and 5cm width, need to fill to about 150 psi
- Gun Freak
- Lieutenant 5
- Posts: 4971
- Joined: Mon Jan 25, 2010 4:38 pm
- Location: Florida
- Been thanked: 7 times
Suit yourself, it won't take long for it to burn out.
OG Anti-Hybrid
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
-
- Specialist 4
- Posts: 458
- Joined: Tue Aug 02, 2011 12:31 pm
- Contact:
ill get one with warranty from somewhere , if it brakes ...see yasco77 wrote:I've actually had luck with a 280psi compressor that was built into a car jump starter pack.. It has filled over 100 times to 200+ PSI
But I still wouldn't recommend it, others probably wont be as reliable.
- Mr.Tallahassee
- Specialist 3
- Posts: 364
- Joined: Sun Jul 10, 2011 2:35 am
I have a 300PSI compressor. It failed to pressurize my chamber beyond 160PSI. It started smoking so I shut it off and popped it open to find that the pump was easily 260 degrees F. I would suggest a homemade hand pump from copper with a long stroke and narrow diameter. With effort, you should be able to get 300-400PSI. Be prepared to have arms of steel after a few shots.
-
- Specialist 4
- Posts: 458
- Joined: Tue Aug 02, 2011 12:31 pm
- Contact:
and how do i make these homemade hand pumps you speak of ?
- Mr.Tallahassee
- Specialist 3
- Posts: 364
- Joined: Sun Jul 10, 2011 2:35 am
Take a look at a bicycle pump. Easy way to do it is to use copper pipe. I left a design here. You may want to use a rubber stopper instead of the floating o-rings and use two check valves, one inlet and one outlet, if you want to use pipe smaller than 1/2''. 1/2'' should give up to 700 PSI if you weigh 150lbs.
I've also had good luck with that very same compressor, trick is, tiny chambers, long breaks, and never run it for more than twenty seconds without the same time for a break. It will go past 300PSI, I'd guess 340 or less, it maxes out the gauge (bad practice I know, I was pressure testing a .177 diaphram launcher).
Mine is now defunct, the hose popped off the barb at the outlet and piloted my launcher, a 1/4 hex nipple will be epoxied over the barb and a snap-air QD threaded on.
Now, I'd never consider using this on my nearly built 1 inch porting launcher, fridgy only.
Mine is now defunct, the hose popped off the barb at the outlet and piloted my launcher, a 1/4 hex nipple will be epoxied over the barb and a snap-air QD threaded on.
Now, I'd never consider using this on my nearly built 1 inch porting launcher, fridgy only.
/sarcasm, /hyperbole