Posted: Fri Oct 12, 2007 6:06 am
Page 2 of 2
Posted: Fri Oct 12, 2007 6:27 am
lol, i would but im not allowed to buy stuff off the net lol.
Posted: Fri Oct 12, 2007 4:52 pm
Its alright, it would have been nice is the stock was blocked off.
I agree jack, it is a bit on the ghetto side...
Cheers,
tsb
I agree jack, it is a bit on the ghetto side...
Cheers,
tsb
Posted: Sat Oct 13, 2007 1:31 am
So im guessing the valve works just fine 
good job
good job
Posted: Sat Oct 13, 2007 2:08 am
yeah the valve works ok. except there is a little leak at the back threads when it gets over about 50 psi. dont know how im going to fix it because i cant take the sprinkler off.
Posted: Sat Oct 13, 2007 2:49 am
JB-Weld is your friend 
Looks like shit if its not painted but it usually does the job.
Did you use teflon tape? If you did try tightening the valve on the threads a bit more.
Looks like shit if its not painted but it usually does the job.Did you use teflon tape? If you did try tightening the valve on the threads a bit more.
Posted: Sat Oct 13, 2007 9:03 am
yes i did use teflon tape. and i tightened them as much as i could. its very tight i cant undo it with my hands lol. i might just use some araldite or something else and go around the threads. i take it up to 50 psi and its fine to shoot though.
taken it up to 80 psi today. put it on my bipod and wrecked my ears haha because the marble was so tight and i havent pushed the barrel through the T so the pressure shot the marble out and blew the bipod apart(not glued, haha)
even shooting a blank at 80 psi is loud as. i would make a silencer for it but not allowed Sad
Shot bb shell at 40psi in my room and it caned me on the neck. missed the target because of a bit of recoil to the side, and a load of BBs got me on the neck. split BB's everywhere and an anihilated cotton wool ball scattered over the floor.
THIS GUN IS AMAZING. very powerful considering other guns ive made.
compressed her up to about 40psi, popped an airsoft bb wrapped in tape through 2 sides of a coke can cleanly at about 5 metres.
taken it up to 80 psi today. put it on my bipod and wrecked my ears haha because the marble was so tight and i havent pushed the barrel through the T so the pressure shot the marble out and blew the bipod apart(not glued, haha)
even shooting a blank at 80 psi is loud as. i would make a silencer for it but not allowed Sad
Shot bb shell at 40psi in my room and it caned me on the neck. missed the target because of a bit of recoil to the side, and a load of BBs got me on the neck. split BB's everywhere and an anihilated cotton wool ball scattered over the floor.
THIS GUN IS AMAZING. very powerful considering other guns ive made.
compressed her up to about 40psi, popped an airsoft bb wrapped in tape through 2 sides of a coke can cleanly at about 5 metres.
Posted: Sat Oct 13, 2007 9:12 am
Try putting a C-clamp on the sprinkler valve and twisting; this should work, but unscrew the blowgun first so the clamp doesn't bend it on accident and stretch the threads holding the blowgun in.
Posted: Sat Oct 13, 2007 9:17 am
use more tef-tape, you should have at least 6 full layers on the threads, thats all i can say/help with..
Posted: Sat Oct 13, 2007 2:30 pm
Dont think so, if you do than im in trouble. On Trade me you can buy 68,000 paintballs in one lot. LOL
Posted: Sat Oct 13, 2007 11:04 pm
Does thread-loc seal threads?
Posted: Fri Nov 23, 2007 9:38 pm
gday man i got a solenoid valve same as theone on your marble sniper but it was my first mod so im not sure if i did i right. can you give me a hand?
cheers
Ant
cheers
Ant
Posted: Sat Nov 24, 2007 9:45 pm
well waht did you do.
ask ummmm pyroninja I THINK
he is good at explaining
ask ummmm pyroninja I THINK
he is good at explaining