Page 2 of 5
Posted: Fri Jan 20, 2012 2:49 pm
by warhead052
evanmcorleytv wrote:warhead052 wrote:If you think 1/4" is gonna be a good barrel, good luck to you. Try 1/8".
1/8 inch is WAY too small!! Use what Gun freak suggested, or just buy an airsoft barrel. 6mm brake line is the cheapest, and the best.
*facepalm* I used 1/8" PEX tubing, 1/8" precision steel tubing, 1/8" brass pipe nipples, they all fit airsoft bb's. Its not too small. And brake line is not the best thing out there....
Posted: Fri Jan 20, 2012 5:44 pm
by Proxywars
Gun Freak wrote:ID of 1/4" type L copper = 0.315"
diameter of airsoft BB = .23622"
Awful barrel.
ID of 9/32" brass tubing = .252"
better barrel.
I wish... I wont find anything smaller but I made the list an I'll go to lowes this week and find the parts I need then make it. =).
Posted: Fri Jan 20, 2012 6:45 pm
by Gun Freak
Whatever floats your boat.
Posted: Fri Jan 20, 2012 7:04 pm
by Proxywars
Okay =p expect a new showcase soon =)
Posted: Sat Jan 21, 2012 12:26 am
by Proxywars
I added new pictures on 1st page.
Firing
is it good?
Posted: Sat Jan 21, 2012 1:48 pm
by Proxywars
I don't understand the ggdt with my gun and also. Do I have to use a tubeless valve? I planned on using my shrader valve from and intertube and strip the rubber off and epoxy some tape to the end of it so it doesn't fly out.
Did I mess up with ggdt?
[/list]
Posted: Sat Jan 21, 2012 2:04 pm
by Mr.Tallahassee
You aren't making a hammer valve gun so I'm not sure why you used it in GGDT. I would also find pipe and tubing diameters as well. .5'' PVC is not .5'' inner diameter. It's actually approximately .62''. I would use a barrel closer to the BB diameter as well. There will be a large gap around the BB in type L 1/4'' copper pipe.
Posted: Sat Jan 21, 2012 2:10 pm
by Proxywars
I won't find anything smaller =/. Since I'm buying parts today. Im using a hammer valve so wat should I put as valve in ggdt? and wat is the inner and outer diameter?
Posted: Sat Jan 21, 2012 2:58 pm
by Gun Freak
You're using using a ball valve...
Posted: Sat Jan 21, 2012 3:08 pm
by Proxywars
Gun Freak wrote:You're using using a ball valve...
See see this is y I need help
. Ya im a serious nooob but im going to lowes right now to pick up the stuff =p
Posted: Sat Jan 21, 2012 3:10 pm
by Gun Freak
Don't even think about hammer valves
You should be able to find everything alright. Just don't ask the idiot employees for help
Posted: Sat Jan 21, 2012 4:59 pm
by Proxywars
I went to lowes and bought every thing. An employee even seen me buying stuff so he said he makes guns too and convinced my mom to buy me a dremel and some teflon tape.
Posted: Sat Jan 21, 2012 5:19 pm
by Gun Freak
Your dremel will soon become your best friend. It is a great tool.
Oh and yeah you need teflon tape... duh.
Let's see it!
Posted: Sat Jan 21, 2012 5:24 pm
by Proxywars
Not home. Ill take pictures of it wen i get bak and progress updated haha
Posted: Sat Jan 21, 2012 6:43 pm
by Proxywars
