Posted: Fri Jun 29, 2012 2:07 pm
No I did not shoot the cannon as the reduction is not stuck ...
I retain the idea of balls
I retain the idea of balls
Your wife must be happyPetitlu wrote:I retain the idea of balls
Page 2 of 2
Posted: Sat Jun 30, 2012 3:03 am
Posted: Sat Jun 30, 2012 3:15 am
yes very !
Posted: Mon Jul 02, 2012 5:41 am
New test, but that the PAL is assembled and glued.
The barrel is made of PVC-P with holes D14mm, covered with transparent polycarbonate.
The rupture disc is aluminum, 7 sheets total, approximately 0.2mm, I did in snitch because I've never used aluminum sheets ... too thick? not enough?
The noise was terrible, a gunshot!
[youtube][/youtube]
The barrel is made of PVC-P with holes D14mm, covered with transparent polycarbonate.
The rupture disc is aluminum, 7 sheets total, approximately 0.2mm, I did in snitch because I've never used aluminum sheets ... too thick? not enough?
The noise was terrible, a gunshot!
[youtube][/youtube]
Posted: Mon Jul 02, 2012 6:04 am
very nice, look quite a bit different to the combustion, if you can put the disc in and fill with air until they burst then you will know if you need more.
Posted: Mon Jul 02, 2012 6:12 am
Very cool! You immediately notice the moment that the disk bursts
So... 1.5x hybrid?
So... 1.5x hybrid?
Posted: Mon Jul 02, 2012 6:16 am
Thank
This is what I do to test my steel discs!
I think the thickness is correct because the combustion is complete when the disc breaks.
This is what I do to test my steel discs!
I think the thickness is correct because the combustion is complete when the disc breaks.
Posted: Mon Jul 02, 2012 6:23 am
To make a Mix1.5 or it will be more complicated because I put the fuel with a syringe fitted with a hose via the union.
The chamber is not obvious breakthrough of pressurize ...
The chamber is not obvious breakthrough of pressurize ...
Posted: Mon Jul 02, 2012 12:31 pm
very nice
even on the video it sounds loud!
would there be a lot of difference between hybrid and athmospheric combustion?
even on the video it sounds loud!
would there be a lot of difference between hybrid and athmospheric combustion?
Posted: Wed Jul 04, 2012 12:23 pm
Here I finished Pyson, this is my last spudgun.
I made several PAC, a hybrid and I end with a PAL original and rather nice.
Background characteristics:
Ratio: 1.61
Discount: 2.35
CHAMBER:
Material: Polycarbonate
Volume: 1450cc
Inside diameter: 80mm
BARREL:
Material: PVC and polycarbonate-P
Barrel diameter: 34mm
Barrel length: 100cm
Volume: 907cc
Barrel screwed to put a rupture disk: Leaves Alu - 8 layers -
Special feature: Holes 150mm 14mm all covered by a transparent polycarbonate tube to see the flames and "follow" the projectile along the barrel.
IGNITION:
Taser
Multipoint Electrode (4)
[youtube][/youtube]
I made several PAC, a hybrid and I end with a PAL original and rather nice.
Background characteristics:
Ratio: 1.61
Discount: 2.35
CHAMBER:
Material: Polycarbonate
Volume: 1450cc
Inside diameter: 80mm
BARREL:
Material: PVC and polycarbonate-P
Barrel diameter: 34mm
Barrel length: 100cm
Volume: 907cc
Barrel screwed to put a rupture disk: Leaves Alu - 8 layers -
Special feature: Holes 150mm 14mm all covered by a transparent polycarbonate tube to see the flames and "follow" the projectile along the barrel.
IGNITION:
Taser
Multipoint Electrode (4)
[youtube][/youtube]
Posted: Wed Jul 04, 2012 9:25 pm
Very impressive. I love the clear chamber. seems you really thought this out and didnt just throw it together. Good work.
Posted: Thu Jul 05, 2012 1:08 am
Thank you!
I also love the flames in the chamber and barrel!
A night firing will be excellent I think
I also love the flames in the chamber and barrel!
A night firing will be excellent I think