Posted: Thu Jun 30, 2011 6:48 pm
*cough*ejaculation video*cough* 
Page 16 of 30
Posted: Thu Jun 30, 2011 7:43 pm
You know what I meant fighter....
Posted: Fri Jul 01, 2011 12:00 am
I knew I should never have told that storyPOLAND_SPUD wrote:mind you that he does have some experience in producing them
Yeah, at least they're in relief, not protruding!Now with those dimples, I'm afraid of the final look...
edit: btw, please tell me we're doing the barrel support before the dimples and squared off ends... I want to fire this thing
Posted: Sat Jul 02, 2011 12:58 pm
Nice!
I was off to Hungary for a week, so I missed it.
There were some guys with machining experience coming along, and we ended talking about cutting fluids. It seems that rapeseed/canola-oil are good
oils to cut with.
I believe eco-friendly chainsaw oil has about 70% rapeseed-oil in it.
It looks like you pick up the skills very fast. The teachers at my school would be very happy if they would have students like you
I was off to Hungary for a week, so I missed it.
There were some guys with machining experience coming along, and we ended talking about cutting fluids. It seems that rapeseed/canola-oil are good
oils to cut with.
I believe eco-friendly chainsaw oil has about 70% rapeseed-oil in it.
It looks like you pick up the skills very fast. The teachers at my school would be very happy if they would have students like you
Posted: Sat Jul 02, 2011 6:07 pm
Right now I'm wishing I made some different career choices.
Time will tell if I can recover
Time will tell if I can recover
Posted: Sat Jul 02, 2011 6:27 pm
Damn... took me forever to find the correct setup to be able to film the mill...
The piece is done, and I will try to finish the movie for tomorrow early afternoon... in the meantime... here's a little teaser
[edit] Silly YouTube 15mn limit! The movie is too big to describe both the lathe and mill operations...
So I'll split it in two. If everything goes well while I sleep first part will be finished uploaded when I wake up
The piece is done, and I will try to finish the movie for tomorrow early afternoon... in the meantime... here's a little teaser
[edit] Silly YouTube 15mn limit! The movie is too big to describe both the lathe and mill operations...
So I'll split it in two. If everything goes well while I sleep first part will be finished uploaded when I wake up
Posted: Sat Jul 02, 2011 8:19 pm
Nice! Looks like its going to be a good video!Posted: Sun Jul 03, 2011 1:42 am
Sexeh!
Go on youtube, I have a pengun to fire!
Go on youtube, I have a pengun to fire!
Posted: Sun Jul 03, 2011 2:51 am
looking forward for your next video
Posted: Sun Jul 03, 2011 5:45 am
Here's the First part of Step 9: The Barrel support
[youtube][/youtube]
[youtube][/youtube]
Posted: Sun Jul 03, 2011 6:16 am
I think someone using your pen gun as a dirty toy at the end LOL
Posted: Sun Jul 03, 2011 6:40 am
sweet! starting now
edit: done!
millmillmillmillmillmillmillmill!
edit: done!
millmillmillmillmillmillmillmill!
Posted: Sun Jul 03, 2011 7:46 am
Clarification, what's the correct way to mount the table to the cross-slide?
Here it's done with brackets:
... but logic tells me it should be bolted directly though the holes provided:
Here it's done with brackets:
... but logic tells me it should be bolted directly though the holes provided:
Posted: Sun Jul 03, 2011 7:50 am
Both are correct, but yes, both holes can be used. You don't need 4 locking points, 3 are enough (remove one one the rounded side).
Be careful not to use screws too long for the holes or you will beump the T slot's internal (guess how I know that).
Be careful not to use screws too long for the holes or you will beump the T slot's internal (guess how I know that).
Posted: Sun Jul 03, 2011 7:55 am
LeMaudit wrote:Both are correct, but yes, both holes can be used. You don't need 4 locking points, 3 are enough (remove one one the rounded side).
Two bolts are provided, aren't they sufficient?