SpudFiles

This is my new copper barrel sealing Tee valved gun... all copper is type L.. i havent got a shot from it due to the epoxy still curing... the over all length is about 56 inches... the barrel is 4 feet... and the chamber is about 37-38 inches... the union is half inch and it is my breech load.... here are some pics Enjoy

That this awesme is thing, sorry about that.
This thing is awesome, what pressure do you take it to?
I would be proud to own this "nug", damage shots or vids?


Edit: What dimentions? , like what calibre?

I like it man. Mya it bring you joy with every shot.

What does the Epoxy have to set in?Don't tell me you epoxied the fittings in.

Don't be afraid to add some damage shots and a video when you can,nice gun always been a fan of copper.

Looks like it will be a nice high-velocity hole puncher when you test it

What pressures are you planning on taking it to? For that chamber size it shouldn't be too hard to get to 250 psi or so with a shock pump which will definitely give you a considerable power advantage.

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.

What dimentions? , like what calibre?

The barrel is half inch and the chamber is 3/4 inch

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.

blind909 wrote:

This is my new copper barrel sealing Tee valved gun... all copper is type L.. i havent got a shot from it due to the epoxy still curing

He wrote that a while ago... SB15 was asking if he had fired a shot yet. Anyways, nice cannon. What is that thing between the female adapter on the piston valve and the other components? It appears to be clear. Also, why did you epoxy the fittings in when you could have soldered them? I am not necessarily challenging the integrity of the fittings, but I am sure that soldering them would allow the cannon to take higher pressures safely. And finally, why is the union so far from the piston valve?

Again, nice launcher. My copper piston rifle is one of my favorite spudguns.

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.

Very nice, now all you need is a co2 setup

What is that thing between the female adapter on the piston valve and the other components?

the thing you are talking about is a compression fitting that i found...

and i did some shooting today before my pump broke, it shot very well...ill add the damage pics with the video i will make soon.

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.

the cans were filled to the top with water