Page 1 of 2
New project started
Posted: Sun Aug 12, 2007 11:02 pm
by frankrede
Coaxial piston rifle.
similar to this one
http://www.spudfiles.com/forums/viewtopic.php?t=2494&
but different.
I need to buy a new bushing because I screwed mine up/
Interchangeable barrels+functional silencer for 1/2" barrel.
This tipic serves as a build log.
Posted: Sun Aug 12, 2007 11:19 pm
by hi
i wish you luck.
Posted: Sun Aug 12, 2007 11:32 pm
by frankrede
Its real easy, 1 1/4" end caps fit nice in 2" sch 40
Posted: Mon Aug 13, 2007 12:08 am
by spud yeti
Sounds good.
Are we all supposed to chip in our current project now?
Posted: Mon Aug 13, 2007 1:42 am
by frankrede
sure sounds good, whats everyone up too?
Posted: Mon Aug 13, 2007 8:12 am
by potatoflinger
I'm in the middle of building an assault rifle, it will have a qev single shot mode, a vortex block full auto mode, and a grenade launcher. So far everything is finished except for the grenade launcher, which will be a diaphragm co-axial. I think I will have it finished in a week or two.
Posted: Mon Aug 13, 2007 8:27 am
by spanerman
im currently fabricating a stand for my hybrid...
Posted: Mon Aug 13, 2007 8:33 am
by judgment_arms
Me, nothin’ much, just building a prototype auto-cannon, and designing 6 more
The prototype should be finished by the end of the week, provided all goes per planed and I get off my lazy butt…
Hey that reminds me, I’ve got a flop to post…
Posted: Mon Aug 13, 2007 9:15 am
by spud yeti
Everyones projects sound really good, and Im looking foward to seeing them all.
I'm finishing my semi-auto paintball gun, which is going well, and will hopefully be completed in the next few months (its about 52% complete(that was just a guess))
I am now starting on a prototype(ish) valve which includes a "hammer-piston" valve; hence the (ish)
that is only in its early stages though, and could be a while...
Posted: Mon Aug 13, 2007 9:18 am
by Fnord
Currently I'm getting parts for a hybrid torture test.
The goal is to find out what it really takes to fragment 2 inch sch40 steel.
(No, I'm not going to blow up my hybrid, I'm going to make a closed hybrid chamber and crank up the mix until it pops)
This will of course be done in bunker. If I can't get it to explode(I'm limited to about 8 or 9x), Then I will adjust the spark gap placement to attempt DDT.
Posted: Mon Aug 13, 2007 9:26 am
by Hailfire753
Whoa! I look foward to a video!
Posted: Mon Aug 13, 2007 9:32 am
by Fnord
Not sure if I will be able to get a video (potential damage to camera and all).
I'll try to see about getting some lexan to set up a camera behind.
Either way you can still expect pictures.
Posted: Mon Aug 13, 2007 9:41 am
by spud yeti
Currently I'm getting parts for a hybrid torture test.
The goal is to find out what it really takes to fragment 2 inch sch40 steel.
(No, I'm not going to blow up my hybrid, I'm going to make a closed hybrid chamber and crank up the mix until it pops)
This will of course be done in bunker. If I can't get it to explode(I'm limited to about 8 or 9x), Then I will adjust the spark gap placement to attempt DDT.
Posted: Mon Aug 13, 2007 9:47 am
by Skywalker
Dang. Awesome projects! Howcome everyone is all of a sudden making lots of semi/auto guns? I can't wait to see all these things and get some ideas.
Posted: Mon Aug 13, 2007 10:00 am
by spud yeti
skywalker wrote:Howcome everyone is all of a sudden making lots of semi/auto guns
Nope, only me making a semi-auto. Look carefully and you would notice every ones making auto guns. The making them because they awesome though