Difference between revisions of "Spark strip"
(Added information about benefits of having spark in centre of chamber. holes in chamber does not really weaken it, but creates failure points) |
|||
| (13 intermediate revisions by 6 users not shown) | |||
| Line 1: | Line 1: | ||
| − | A spark strip is used to provide multiple sparks | + | [[Image:Spark_strip.jpg|frame|An etched copper spark strip]]A '''spark strip''' is used to provide multiple sparks to ignite the fuel/air mix in a [[combustion launcher]]. It is differs from multiple [[spark gap]]s in that a spark strip is mounted using two or even one [http://www.advancedspuds.com/his.htm (temp link)] hole. This is done primarily to ensure the integrity of the launcher, as drilling multiple holes in the [[chamber]] creates more possible failiure points. Spark strips can also be used in [[coaxial]] launchers, where chamber space is more cramped. |
| − | + | A spark strip consists of several conductive objects in a row with a short gap in between, effectively forming a line of spark gaps. As with other spark gaps, the combined width of the gaps must be small enough for the [[ignition source]] to overcome. | |
| − | |||
| − | |||
| − | + | There are several ways to achieve this: | |
| − | Small | + | ===scratched conductive film=== |
| + | By scratching thin lines across a conductive film (metallic paints, CDs) it is possible to get very large numbers of sparks out of a meager source. A more sophisticated method consists of etching a spark strip pattern in a printed circuit board. | ||
| + | |||
| + | ===Wire method=== | ||
| + | Small pieces of wire, such as from a coathanger are glued to the wall. Gaps between each piece of wire cause a spark to be produced. | ||
| + | |||
| + | ===Veroboard=== | ||
| + | |||
| + | Veroboard is a ready-made circuit board with multiple copper strips or dots, a piece cut perpendicular to the copper strips will function as a spark strip. | ||
| + | |||
| + | Spark strips are sometimes seen as inferior to a screw based gap system, because they are often mounted on the wall of the chamber, as opposed to screws, where the spark is in the very centre of the chamber. This means that the flame from can only travel in one direction (away from the wall). A central gap allows the flame fron to spread in every direction towards the walls. | ||
| + | [[category:Components]] | ||
Latest revision as of 15:13, 16 June 2009
A spark strip is used to provide multiple sparks to ignite the fuel/air mix in a combustion launcher. It is differs from multiple spark gaps in that a spark strip is mounted using two or even one (temp link) hole. This is done primarily to ensure the integrity of the launcher, as drilling multiple holes in the chamber creates more possible failiure points. Spark strips can also be used in coaxial launchers, where chamber space is more cramped.
A spark strip consists of several conductive objects in a row with a short gap in between, effectively forming a line of spark gaps. As with other spark gaps, the combined width of the gaps must be small enough for the ignition source to overcome.
There are several ways to achieve this:
scratched conductive film
By scratching thin lines across a conductive film (metallic paints, CDs) it is possible to get very large numbers of sparks out of a meager source. A more sophisticated method consists of etching a spark strip pattern in a printed circuit board.
Wire method
Small pieces of wire, such as from a coathanger are glued to the wall. Gaps between each piece of wire cause a spark to be produced.
Veroboard
Veroboard is a ready-made circuit board with multiple copper strips or dots, a piece cut perpendicular to the copper strips will function as a spark strip.
Spark strips are sometimes seen as inferior to a screw based gap system, because they are often mounted on the wall of the chamber, as opposed to screws, where the spark is in the very centre of the chamber. This means that the flame from can only travel in one direction (away from the wall). A central gap allows the flame fron to spread in every direction towards the walls.
