Paintball sniper

Cannons powered by pneumatic pressure (compressed gas) using a valve or other release.
Post Reply
Moggle NZ
Private 2
Private 2
Posts: 22
Joined: Sat Jan 21, 2012 1:03 am

just a picture of the setup i might use just wondernig what i can in pvove on such as
metirals
airflow
just any thing

when u pull the bolt back the ball valve will open
and close when u push formards so u can have muliple shots


Image


wh
Top
User avatar
jrrdw
Moderator
Moderator
United States of America
Posts: 6572
Joined: Wed Nov 16, 2005 5:11 pm
Location: Maryland
Has thanked: 39 times
Been thanked: 22 times
Contact:
Contact jrrdw

Looks like your air will be restricted. That's good for repeated shooting but bad for power.
Top
User avatar
Gun Freak
Lieutenant 5
Lieutenant 5
Posts: 4971
Joined: Mon Jan 25, 2010 4:38 pm
Location: Florida
Been thanked: 8 times

Not a very practical design. There are easier ways to do it. Why a hammer valve and a ball valve?
OG Anti-Hybrid
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
Top
Moggle NZ
Private 2
Private 2
Posts: 22
Joined: Sat Jan 21, 2012 1:03 am

that is why i posted it asking for halp then u just tell me whats bad not tell me what i can do to impove it
Top
User avatar
Gun Freak
Lieutenant 5
Lieutenant 5
Posts: 4971
Joined: Mon Jan 25, 2010 4:38 pm
Location: Florida
Been thanked: 8 times

1. Too much dead space

2. Bolt is overly complex

3. Make the air chamber one part (not two with a ball valve)

I would like to say though that the actual valve part looks doable with a little creativity. But, what pressure are you going to use? It will take a lot to get paintballs flying.
OG Anti-Hybrid
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
Top
Moggle NZ
Private 2
Private 2
Posts: 22
Joined: Sat Jan 21, 2012 1:03 am

ok thanks gun freak i was thinking instead of a valve useing a solenoid valve is
15mm an ok size
or shud i opt for the bigger 25mm
i would prefur the smaller 1 for look reasons only
Top
User avatar
Gun Freak
Lieutenant 5
Lieutenant 5
Posts: 4971
Joined: Mon Jan 25, 2010 4:38 pm
Location: Florida
Been thanked: 8 times

I'm no sure you can get multi-shot on a ssolenoid valve... Have you given thought to a three-way valve?
OG Anti-Hybrid
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
Top
Moggle NZ
Private 2
Private 2
Posts: 22
Joined: Sat Jan 21, 2012 1:03 am

you can ive seen it done b4
Top
Moggle NZ
Private 2
Private 2
Posts: 22
Joined: Sat Jan 21, 2012 1:03 am

is a 15 mm solenoid valve an ok size for this gun?
Top
Post Reply

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Register

Sign in

  • Similar Topics
    Replies
    Views
    Last post

Return to “Pneumatic Cannons”