epoxy ammo molds

16 posts

trae08: Corporal; Posts: 520; Joined: Sun Jul 09, 2006 2:14 pm; Location: florida

Quote

Sun Sep 16, 2007 1:54 pm

kool let us know what happens.

Marvin the Martian: Where's the kaboom? There was supposed to be an earth-shattering kaboom!

Marvin the Martian: The Earth? Oh, the Earth will be gone in just a few seconds.

PCGUY wrote:Congrats, your the first donating member I have had to ban.

Post Reply

16 posts

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Sign in

Similar Topics

Replies

Views

Last post

Casting Epoxy from Molds

Last post by metalmeltr « Wed Mar 17, 2010 8:36 am
Posted in General Cannon Discussion
Replies: 4
by zomgwtfbbq » Mon Mar 15, 2010 1:10 am » in General Cannon Discussion

First post

Is it possible to cast low-viscosity epoxy resin into a mold and taking it out of the mold?

P.S. Like perhaps putting a layer of grease onto the...

Last post

I belive that the casting epoxy that you are refering to is a ployester resin and in that case I would saythat you are better off using JB weld or a...

4 Replies

1632 Views

Last post by metalmeltr
Wed Mar 17, 2010 8:36 am
Metal Epoxy Putty, and Ammo

Last post by Gun Freak « Fri Jan 03, 2014 7:27 pm
Posted in Ammo & Materials
Replies: 1
by sagthegreat » Fri Jan 03, 2014 12:22 pm » in Ammo & Materials

First post

I am making a coaxial, would metal epoxy putty work to attach the barrel to the end cap?

It has a 900psi tensile strength, has anyone used this...

Last post

It might hold it but epoxy putty doesn't have great adhesive qualities, more for strength. Plus it wouldn't perfectly fill the gap because it's not a...

1 Replies

3189 Views

Last post by Gun Freak
Fri Jan 03, 2014 7:27 pm
Aluminum Molds

Last post by noname « Tue Sep 18, 2007 9:30 pm
Posted in Ammo & Materials
Replies: 16
by noname » Sun Sep 09, 2007 8:32 pm » in Ammo & Materials
1

2
First post

Does anyone know of anything I can use for a mold, that can handle molten aluminum? I've made a couple out of plaster of paris, but I'm not sure if...

Last post

Just your average flowerpot furnace; costs about $10 to get it running for a few weeks.
16 Replies

4791 Views

Last post by noname
Tue Sep 18, 2007 9:30 pm
lube on piston molds

Last post by VH_man « Sat Jul 19, 2008 4:45 pm
Posted in Ammo & Materials
Replies: 13
by Sticky_Tape » Thu Jul 17, 2008 2:08 pm » in Ammo & Materials

First post

I need to know what typr of lube you can use on piston molds for a plunger on my pump I tried to use wd40 on a small piece of 1/2 copper and poured...

Last post

yea, BTW sillicone lube does not work for moulding pistons.

it dissolves into the epoxy, weakening it and making kind of hard to remove.

stick with...

13 Replies

2801 Views

Last post by VH_man
Sat Jul 19, 2008 4:45 pm
Cement molds and making cement slugs

Last post by windshrike « Fri Oct 19, 2007 3:44 pm
Posted in Ammo & Materials
Replies: 18
by gwoloshyn » Thu Oct 18, 2007 8:28 pm » in Ammo & Materials
1

2
First post

For my new air cannon, which I will post this weekend when I finish it, is going to shoot these cement slugs I made. Pretty straight forward, cut pvc...

Last post

Make it a bit small and wrap it in duct tape to prevent wear in the barrel.
18 Replies

8151 Views

Last post by windshrike
Fri Oct 19, 2007 3:44 pm

Return to “Ammo & Materials”

epoxy ammo molds

Create an account or sign in to join the discussion

Create an account

Sign in

Login • Register