I got HPA...Near SOS shots...

[jeepkahn]

I got me a pure energy 3k tank w/850psi reg and an inline reg to drop it between 200-500...

Using my copper cane gun, at 400psi i got readings of 1094, 1103, 1107, 1098... this was using yellow wire nuts for ammo and 4ft between muzzle and chrony...

temp was 87f, humidity was 91%, and 1312 ft above sealevel...

I did fire a coupla shots with 500psi but it had gotten too dark for the chrony to pick them up, After I refill my tank today I'll inch up the pressure a little....

With .5" bearings the readings were in the 750-800fps range... but they are a bit loose in the barrel, they do however go all the way through a healthy/not rusty 55 gallon drum...

[thedeathofall]

With .5" bearings the readings were in the 750-800fps range... but they are a bit loose in the barrel, they do however go all the way through a healthy/not rusty 55 gallon drum...

With ammo like that, they should. That is some serious power your packing!

[jeepkahn]

http://www.spudfiles.com/forums/pics-no ... 17705.html

link to the launcher I'm refering to...

I'll see if i can get some pics of my tank and reg setup sometime today...

here's internet pics of the components I'm using...

[Ragnarok]

temp was 87f, humidity was 91%, and 1312 ft above sealevel...

Which would make the SOS about 1148 fps.

With that distance between the muzzle and chrony, you're probably getting pretty genuine readings.
I still have doubts you'll actually go supersonic even with an extra 100 psi on top of that, but doubtless you'll get closer.

[jeepkahn]

temp was 87f, humidity was 91%, and 1312 ft above sealevel...

Which would make the SOS about 1148 fps.

With that distance between the muzzle and chrony, you're probably getting pretty genuine readings.
I still have doubts you'll actually go supersonic even with an extra 100 psi on top of that, but doubtless you'll get closer.

I figured if I gave atmospheric specs you'd chime in with the actual sos for conditions.... I'm gonna take the vacuum pump home to9nite to see how much differance it makes and if it'll put me over the edge of sos...

[thedeathofall]

nice setup there. What kind of a regulator is that?

[mobile chernobyl]

That's the empire Inline Regulator.

I need to get an LP reg for my 92/45 tank. I want to push my copper cannons up to 300psi and see what they can do... the 50 cal should be fast, but the 75 cal should be balls sick nasty... I'm pretty sure it will be nothing short of amazing lol.

[jeepkahn]

It was nasty and rainy last nite when I got home so I didn't get to play, but this morning I springloaded the fill nipple check to prevent accidentel missfires when disconnecting, and bumped the reg up to 500psi(the newly sprung check requires 38psi to crack, does anyone know if there's an easy way to calculate fill pressure if you know the cracking pressure of the valve, or do I need to set up a rig to gauge both sides of the check???)
I took a coupla shots to get a feel and it's strong... hopefully will stop raining and I can get some more chrony readings later...

[Technician1002]

It was nasty and rainy last nite when I got home so I didn't get to play, but this morning I springloaded the fill nipple check to prevent accidentel missfires when disconnecting, and bumped the reg up to 500psi(the newly sprung check requires 38psi to crack, does anyone know if there's an easy way to calculate fill pressure if you know the cracking pressure of the valve, or do I need to set up a rig to gauge both sides of the check???)
I took a coupla shots to get a feel and it's strong... hopefully will stop raining and I can get some more chrony readings later...

I'm guessing that it will take 35 LBS differential to lift (crack) the valve. 38 into zero, or 500 into 462 would be my guess. Any reason it would be different at pressure?

[jeepkahn]

I was just thinking along the lines of it may act similar to a popoff, it takes xPsi to crack it and yPsi for it to close against a flow due to when closed the pressure only acts on the diameter of the orifice, but once opened it's acting on the diameter of the sealing face.......