Hybrid Confusion

[judgment_arms]

After consulting the Wiki I have bean left with even more questions.
First off and the biggest question: will this work? If I take a pressure chamber fill it with enough propane for combustion and the pressurize it to 100psi and touch off the propane will it go off or not??? The reason I ask this is because in the Wiki it says
“A hybrid is first injected with fuel, then with pressurized air. The amount of air depends on how much fuel was added, and is calculated to achieve a stoichiometric fuel/air ratio in the chamber. A hybrid using twice as much fuel and air as a comparable combustion gun is said to be using a 2X mix, higher mixtures can be used and will produce even higher pressures. The fuel and air needs to be measured and matched carefully to ensure reliable operation, pressure gauges and fuel meters are used for this.”.
So now I’m utterly confused… I thought I understood it but now I don’t know…
Great…after typing all this, except the quote which I copied, I have forgotten my other questions…. I’ll ask them later this one is the most Important…
Forgive me if I sound like a newb, I just don’t want a pipe bomb, or a big waste of money.

Edit:
In a hybrid do you measure stuff by pressure? i.e. 100psi of propane to 100psi of air??? Or is there some other ratio??

[benstern]

no.
4.19851% is the amount of propane to air.
(yes I memorized that number)

[judgment_arms]

Can I get a little more information on that?
Allow me to rephrase my first question: lets say I have a burst disk cannon, the burst disk bursts at 150psi, and I fill it too 100psi and add propane, the exact amount of which I’m not sure at this point, and attempted to touch it off. Will it go off? Will if generate enough pressure to burst the burst disk? Yes I know I’d need to put the propane in first it was just easier to say/type/understand this way.

[benstern]

Yes it will go off easily at that mix. which would actually be a 7.8x mix
at that mix the burst disk should be around 250 psi

[judgment_arms]

Well I was planning on using coke bottle disks as my burst disk, so that’s why I said 150, and I was also planning on using 11/4inch SCH40 PVC…I’m guessing that I should try something else…
Next question:
If the burst disk goes at 150psi and the pipe’s rated to 300psi would the afore mentioned mix be safe??? Since the burst disk goes at 150psi the pressure should never exceed that or at least not for a long amount of time…

[frankrede]

Hold on I'm confused, filling it to 100psi?

[judgment_arms]

Basically what I want is a burst disk gun trigged by a pressure spike generated by the combustion of propane. This whole thread is a result of me doing research for a proposed automatic cannon as read about here: no burst disk hybrid
Since I don’t need that much pressure I’ll just reduce the mix…which means math, YEA

[benstern]

a 7.8x mix has never been done.
it is way too powerful for plastic pipe.

[judgment_arms]

Figures… so anybody want to recommend a mix, please? Sorry I’m lazy… 2x, 2.5x, 3x, 1.495x?

[benstern]

2x to 2.5x would be sufficient

(post 300)

[Killjoy]

Ive got a question thats kinda related to this. Ive been desighing an all steel hybrid (everything rated to 3000 psi or more), and i am planning to use oxygen and acetylene, but im not exactly sure how to meter the oxygen. How exactly would i do that?

[judgment_arms]

From what I’ve read you can’t use oxyacetylene for fuel it’s considered an H.E. I think…

[frankrede]

No its not.

[sergeantspud2]

What is the top/maximum pressure that a hybrid can reach with the most combustible fuel (Im guess acetylene) and air (not oxygen) and a 2x mix?

[judgment_arms]

[quote=frankrede] Hold on I'm confused, filling it to 100psi? [/quote]
[quote=frankrede] No its not. [/quote]

Are you sure???
And I meant it’s like H.E. in the fact that it burns VERY rapidly and that blast is hard to contain. Plus somebody else said it’s like H.E. in another thread.